1 / 8
Statues of Campanile di San Marco (St. Mark's Bell Tower) - Venice, Italy — zdjęcie 1
1 / 8

Statues of Campanile di San Marco (St. Mark's Bell Tower) - Venice, Italy

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Sculpture and relief statues that belong to the assembly of St. Mark's Bell Tower, a separate model.

Ocena
0 / 5
Polubienia
7
Pobrania
95
Wydruki
0
Wyświetlenia
383
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Sculptures
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

These models are statues that belong in our St. Mark's Bell Tower model, and are a separate publication because they are remixed from third-party existing models, and we are respecting their original license.  If you are building the assembly of the bell tower, please print these too and add them where indicated further below.

The belfry is topped by an attic with effigies of the Lion of St Mark and allegorical figures of Venice as Justice. The tower is capped by a pyramidal spire at the top of which there is a golden weather vane in the form of the archangel Gabriel (from Wikipedia).

These models were made by Dany Sánchez by remixing the following existing sources:

  • Maiwand Lion (https://www.myminifactory.com/object/3d-print-maiwand-lion-in-forbury-garden-reading-uk-2957)
  • Wing (https://www.myminifactory.com/object/3d-print-sculptris-obj-bits-wings-and-tails-58747)
  • Allegory of Justice (https://www.myminifactory.com/object/3d-print-allegory-of-justice-66421)
  • Stemma of San Marco (https://www.myminifactory.com/object/3d-print-stemma-of-san-marco-86557)
  • Angel in Cemetery (https://www.myminifactory.com/object/3d-print-angel-in-cemetery-85506)

Sources from ScanTheWorld and DutchMogul on MyMiniFactory

License CC 4.0 https://creativecommons.org/licenses/by-nc-sa/4.0/

 

Print these in order to complete your assembly of St. Mark's Bell Tower (Campanile di San Marco) in Venice!

 

If you like our work, consider joining our Printables Club for monthly exclusive models!

We are also on Patreon!

patreon.com/MiniWorld3D

Find all our profiles, YouTube channel & social media on:

linktr.ee/miniworld3d

Follow us on IG!

instagram.com/miniworld3d

MiniWorld 3D is a collective of 60+ artists creating the best library of 3D printable models of landmarks of the world!

Photo credits: by Dany Sánchez in a Prusa MK4 with Fillamentum turkey egg PLA, Amolen brick, 3D Hojor silk gold PLA. 
 

-----------

Printing Tips

No supports needed, this has been optimized to eliminate all overhangs.

Suggested parameters:

Without input shaper, print slow for better details: 15 or 20mm/s for outer perimeters.
Fine-tune retraction to avoid stringing.
Perimeters: 2
Top layers: 3
Infill: as low as 12%, lightning pattern ok.

Print the Justice and Lion panels flat on the bed, and you can use pause-and-filament change to start with brick, then to marble at the right height. 

The Archangel could use a brim or raft to ensure a good adhesion.

Tagi