XL / Parametric Steel Sheet Holder (fits XL, MK, Mini, X1C, etc.)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Remix of Chewey's remix of Whity's sheet holder. Parametric to fit any sheet size. Includes files for XL, MK4, Mini, X1C
- Ocena
- 5 / 5
- Polubienia
- 25
- Pobrania
- 81
- Wydruki
- 5
- Wyświetlenia
- 485
- Oceny
- 5
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Accessories
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
I loved the idea of Whitys' steel sheet holder with the pushbutton eject mechanism, and then I saw Chewey's remix with the seesaw pusher that seems like it may be a little more robust. Unfortunately, the original and the remix both only had sizes for the MK3/MK4 and the Prusa Mini, and I have an XL.
After trying and failing to import the STL and TinkerCAD files into Fusion 360 without errors, I decided to rebuild the side rails from scratch as a parametric model. These new rails are designed to work with all of the same internal parts that Chewey designed. The only exception is the pushrod, which started with ScottW's slightly longer rod, and was then also made parametric so that it will resize along with the rails.
I've included ready-made STL files for:
- Prusa XL
- Prusa MK3/MK4 series
- Prusa Mini (not tested – I don't have one)
- Bambu X1C (not tested - I don't have one)
These STL files are for the four parts of the side pieces, plus the pushrod in the correct length.
I have re-uploaded the unchanged STL files for the other internal components of Chewey's design so that they are all in one place. You need to print one set of those four items for each holder.
Note: Although my remixed rails are a very close match to Chewey's, the screw positions may be slightly different, so not suitable for mix & match. If you've already printed some of Chewey's that fit your sheets, just print more of those if you need more. I think something like these mounting brackets should work with my version, but I haven't tried them. It's the holes in the middle of the rails that are most likely to not align with Chewey's.
Printing
Print with 0.2mm layer height. If you choose to print at a different height, you may want to use the parametric model and adjust the LayerHeight parameter (see below). I used 25% infill.
Because these rails are longer than the build sheet is deep, they need to be printed diagonally if you're printing them on the sheet they're meant to hold. Save some time by printing the parts for your smaller printer's sheets on your bigger printer if you have one. I printed my MK4 rails on my XL so I was able to print two full sets without angling them, but for the XL, I had to rotate the parts and do one set of right sides at a time. The left sides just barely fit two sets onto the build sheet – see the photo. This was fussy enough that I have provided the 3MF for two sets of left rails on one XL sheet.
For the XL, I rotated parts 45° to fit on the bed. Whity recommended 50° for the MK and 42.5° for the Mini in his original instructions, and I would follow his advice.
Note: If you rotate the parts to fit the sheet, rotate the infill angle by the same amount. i.e., if the default infill angle is 45° and you rotate the parts 45°, set the infill angle to 90°.
The counterbores and the nut recesses have been created using the bridging technique from Maniacal Labs so that they print without requiring support.
I do think that the XL's sheet size may be nearing the practical limits of this design as-is, because the sheets sag a little bit in the middle. An even larger printer might need a modification to the side rails that would provide support farther in from the edges to keep the sag within reason.
Using the Parametric Model
If the ready-made STL sizes don't work for your sheets, you can use the parametric Fusion 360 model. The important parameters are marked as “Favorites” within the file:
- SheetSize: This is the dimension from the frontmost edge of the build sheet (including any tabs on the front, as on the XL), to the back edge at the corner. If the sheet has tabs on the back, do not include those tabs in your measurement unless they are at the corners. See the annotated photo of the XL sheet. If this dimension is correct, the front of the sheet should be flush with the flat portion of the side rail (just even with where the bevel begins – see the photo of the MK3 sheet).
- SheetCornerRadius: This is the radius of the back corners of the sheet. It's important to get this right so that the sheet sits flush with the stop on the back of the rail so that the pusher can get full travel. I like this handy radius gauge to find dimensions like this. If in doubt, err on the side of a smaller radius, because if the radius is too large, it will prevent the sheet from sliding all the way to the back.
- ScrewBore: This is the size of the hole for the shaft of the screw. It's supplied set for an M3 screw.
- ScrewCapDepth: This is the depth of the counterbore for a cap-head screw (or for a button-head M3 wood screw). It is sized so that an M3 cap head screw will be slightly recessed
- ScrewCapDiameter: The diameter of the counterbore for the M3 cap head screw. It is sized for an M3.
- NutSize: the size of the recess for the nuts. Measured from flat face to the opposite flat face. Comes sized for M3 nuts.
- NutDepth: The depth of the recess for the nuts. This is sized so that an M3 nut will sit slightly recessed.
- LayerHeight: This is used to build the bridges for the no-support counterbores. As provided, assumes a 0.2mm layer height.
With the dimensions set as provided, so that an M3 cap head screw and the corresponding nut both sit slightly recessed, an M3 x 6mm screw will fit perfectly, and an M3 x 16mm screw will go through two stacked sets of rails and fit perfectly.
Assembly
Mounting the first holder to the table or shelf is fussy. The two sides need to be perfectly parallel, and the bracket spacing needs to be wide enough that the sheet moves freely, but close enough that it doesn't just become askew and jam when the mechanism tries to push it out. Once the first one is properly installed, adding more is easy.
Here's the method that worked for me.
After printing and assembling all the parts for each side, add M3 nuts to half of the holes in the top piece for each side (see pictures).
Use a set of M3 x 6mm screws through the bottom halves and up into these nuts to attach the upper and lower halves together. If you're only installing a holder for one sheet, these screws will remain in place. If you plan to mount holders for more sheets, then these screws will be temporary, but they make it much easier to mount! Installing these M3 screws now also helps to ensure that the nuts are pulled fully into their sockets, if the fit is a little snug. That will be important if attaching additional holders.
This is a good time to make sure that the pushbutton mechanism works smoothly and adjust if necessary.
Now, clamp one side of the holder to the table or shelf and take a little time to get it positioned properly. It's very important that it is perfectly perpendicular to the front edge of the table/shelf. The front of the holder should be flush with the front of your table/shelf, or slightly recessed. Don't go too far back or you won't be able to grab the sheet once it's ejected.
With the side rail clamped in the correct spot, pre-drill through the empty holes for M3 wood screws. Then, using button-head or cap-head M3 wood screws, attach it to the shelf/table. I think button-head screws are probably more forgiving of imperfect pre-drilling. (Pre-drilling is important here because M3 wood screws can be pretty easy to shear.)
With one side installed, clamp the other side to the table, and use a steel sheet to set the correct spacing. You need these side rails to be far enough apart that the sheet slides freely, but not so far apart that the sheet can rotate and bind up when the button is pushed. With one side installed and the other clamped, you should be able to test that the button ejects the sheet smoothly.
Once the spacing is perfect and everything operates smoothly, pre-drill and use screws to attach the second side. Re-check that everything functions properly.
If you are only mounting one holder, you're done!
If you are attaching additional holders, on the second holder, put nuts into the opposite set of holes from the ones you used on the first holder (i.e., they go into the holes where you put the wood screws on the first one). Use M3 x 6mm screws to secure the upper and lower pieces of the second holder together.
Next, remove the temporary M3 x 6mm screws you installed earlier in the first holder. The wood screws are keeping the first holder together now, and we need to attach the second holder to the first using that set of holes and nuts.
Finally, position this second holder under the first, and use M3 x 16mm screws to attach the second holder to the first. These screws go through both holders and up into the nuts on top of the first one.
If you are adding 3, 4, 5 holders, just repeat this process. Alternate which set of holes you put the nuts into on each layer.