"You'll shoot your eye out!" Voron filament spool holder
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
My spin on a minimal friction spool holder for Voron printers that use 4.5 mm BBs for smooth spool rotation.
- Ocena
- 0 / 5
- Polubienia
- 5
- Pobrania
- 4
- Wydruki
- 0
- Wyświetlenia
- 184
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Voron Parts & Upgrades
- Licencja
- GNU General Public License v3.0
NOTE: this is a work in progress. The V0 and Switchwire models are complete and tested. The Trident/2.4 model should work but is un-tested. Once my Trident is built, I'll update the model if necessary.
Description
This model provides a replacement spool holder for the Voron V0, Switchwire V2.4 and Trident printers. Each spool holder is completely 3d printed except for 20 4.5 mm BBs (Raphie's ammunition of choice!), two M3 threaded heat inserts, and two M3x6 (or M3x8) screws. The hardware is needed for assembly of the spool holder. Additional M3/M5 screws may be required to mount the spool holder to the printer frame.
Installing the ball bearing (BBs) into the tumbler
The tumbler is designed to accept standard 4.5 mm BBs. Each end of the tumbler will accept 10 BBs. Before assembling the tumbler, remove the print-in-place support from the end of the tumbler using needle-nose pliers.



Steps to build the tumbler:
- Using a soldering iron insert 1 M3 threaded heat insert into 1 bearing hub.
- Repeat the previous step with the second bearing hub.
- Stand the tumbler on one end.
- Set 1 bearing hub in the tumbler end with the threaded insert visible. (see image 1 below).
- Slide the bearing hub to one side and drop 4-5 BBs into the opening (see image 2).
- Orient the installed BBs opposite of the indentation in the tumbler, then line-up the indentations in the tumbler and the bearing hub.
- Place another BB in the indentations (see image 3).
- Using a flat head screwdriver, press the BB into the space between the hub and tumbler (see image 4). Note: this may take a moderate force.
- Go to step 6 above and repeat until all 10 BBs are installed
- Flip the tumbler and repeat steps 4-9. The installed BBs are shown in image 5.
Following are images of the BB installation (Note: the threaded heat inserts were not installed first in the images below. It is best if the inserts are installed first).
Image 1:
Image 2:
:
Image 3:
Image 4:
Image 5:
:
V0.2
The V0 spool holder arm has two versions, one for a V0 that has the back panel installed and one where the back panel is not installed. If you choose to install install the spool holder on a printer with a back panel, you may need to mirror the arm in the slicer so it will align properly with the panel. Note M3 screws needed to mount rotating tumbler should be either M3x6 or M3x8.

Parts for V0.2 without back panel installed:

Parts for V0.2 without back panel installed:

The assembled V0.2 spool holder:
Switchwire
Note M3 screws needed to mount rotating tumbler should be either M3x6 or M3x8.


Parts for the Switchwire spool holder:
The assembled Switchwire spool holder:
V2.4/Trident
Note M3 screws needed to mount rotating tumbler should be either M3x6 or M3x8.

Parts for the V2.4/Trident spool holder:

The assembled V2.4/Trident spool holder: