1 / 8
Filamentcutter For Dragonburner/Rapidburner and Sherpa mini/Orbiter V2 levered — zdjęcie 1
1 / 8

Filamentcutter For Dragonburner/Rapidburner and Sherpa mini/Orbiter V2 levered

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

this is an evolution of my DB/RB Filamentcutter

Ocena
5 / 5
Polubienia
163
Pobrania
519
Wydruki
3
Wyświetlenia
4078
Oceny
3

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
GNU General Public License v3.0

If you like me parts, you can also support me here: https://buymeacoffee.com/andretheengineer :)

Hello 3D Printing friends. The idea for a filamentcutter arose after i installed an ERCF on my Voron 2.4. But none of the existing could satisfy my needs. 

This Model is not fully tested. i can successfully cut my filament without problem but i have no idea how this straigns the steppers or any other part.

This Model is made for a V2.4 with Rapidburner, Phaetus Rapido UHF, Sherpa crew mini, Tap. But will probably work with any DB/RB toolhead + sherpa mini.

I dont take any responsibility for injury, you work with sharp objects, please be carefull!

the cutter needs way more force to cut through PLA than ABS from some testing. Keep in mind, that this is designed for changing between ABS filaments and not PLA. You may break your cutter/printer when using any ither filament than ABS/ASA

BOM: 

  • 2* M3x50 (full thread or Partial)
  • 2* M3 Nut
  • 2* d6x3mm magnet Or 4-5mm Spring
  • a cut off part of a 5.9mm wide blade (about 11mm from the blade tip)
  • 2* M3x14 (or 16)
  • (superglue)

Recommended Tools

  • Superglue
  • 2 & 2.5 mm Allen Key
  • highly recommended M3 tap
  • something to cut the blade short (dremel works very good for me)

Assembly:

  • print all parts in the provided orientation with the regular Voron PIF profile
  • insert a magnet in Base Bottom magnet hole
  • glue in another magnet into the slider so the magnets OPPOSE each other (S to S or N to N)
  • Insert M3 Nuts in the Base Top and Bottom
  • tap the magnet side of the Slider with the M3 tap (if not the slider may crack when installing the screws) (optionally print the slider upright)
  • glue in the blade into the slider (push it gently in its cavity with something plasic)
  • Screw the M3x50 in the Slider from the blade side that about 4-5mm of threads stick out the Magnet side
  • encase the M3 Screw heads with the Arm part, slide over the middle hole of the lever and secure with M3x14 screw
  • Place the slider assembly in the bottom Part and close up with the top part
  • secure the Lever with M3x14 screw in the dedicated hole
  • now place the whole assembly between your Printhead and extruder and secure with 8mm longer screws than original if you add this on its own

Optional:

  • Print the Filament Cutter Arm in the Provided Orientation (if you have Extrusion Backers use that) 
  • Screw that on the left side Extrusion with M3x20 and TNuts
  • Use a M5x40 (or 45) Screw to have a point where the cutter can ram against

Tagi