1 / 4
FluidDial Pendant CRADLE v2.2 - for LowRider v4 (attaches to YZ plate on X-min side) — zdjęcie 1
1 / 4

FluidDial Pendant CRADLE v2.2 - for LowRider v4 (attaches to YZ plate on X-min side)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Also see description for link to FluidDial Case that supports Bart's starter kit.

Ocena
0 / 5
Polubienia
32
Pobrania
145
Wydruki
0
Wyświetlenia
1501
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Tools
Licencja
Creative Commons — Attribution — Noncommercial

Heads-up: There's a new version of this: v2.3 — The only change in that remix was to make a bidirectional version of the cradle. Works no matter which side of the gantry you attach it. — Get it here:  https://www.printables.com/model/1262328-fluiddial-pendant-cradle-v23-bidirectional-for-low 

Major kudos to Ryan of V1 Engineering for releasing the LowRider v4 CNC!

This FluidDial CRADLE v2.2 is for the LowRider v4 (attaches to YZ plate on X-min side). 

If you wanted the older one that was designed for LowRider v3 (and basically can attach to any smooth surface), please see here: https://www.printables.com/@design8studio/models?search=cradle

I have two remixes of printed cases for the FluidDial pendant:

Notes for printing and installing:

  • Print as oriented.
  • Prints without need of supports (new as of v2.2).
  • Designed for use of magnets added to cradle and pendant base. Use 8 sets of tiny round magnets, nominally 2mm thick x 5 mm diameter — in total, 16 small magnets. This affiliate link leads to the magnets used: https://amzn.to/3NSjTbe 
  • Cradle attaches to the LowRider v4 YZ plate on the X-min side, using three (3) M3 screws. Various length could work. 

For more info (videos and links):

 
LR4 cut videos:

Above is my most recent video on the LowRider v4 DIY CNC - It's a Beta version test cut - Amazing hardwood cut at 3000mm/min (50mm/sec) at 12mm depth of cut. 1/4” 1-flute carbide up-cut end mill from V1E.com. Kobalt router at about 4 or 4.5 on the dial! Step-over rate: 75%. Jackpot control board from V1E.com running FluidNC firmware. TMC2209 drivers powering the NEMA 17 stepper motors at 0.8 amps. They were staying so cool!

Links:
Note:

This was designed during pre-release testing, initially for Release Candidate 3, but I have verified that it's compatible with the final release of the LowRider v4. Thus, the screen shots of the 3D models show RC3. No worries, it fits the final, released LR4 version.

Change log:
  • Oct. 23, 2024 — revised 2.2 prints without need of supports (new as of this revision), and the notch is deeper (it needed to be to accommodate the cord even when using Bart's starter kit).
  • Oct. 22, 2024 — revised 2.1 has deeper notch that accommodates the cord even when using Bart's starter kit.
  • Oct. 12, 2024 — initial upload of v2.0


My PayPal tip jar: https://paypal.me/design8studio 


*Any Amazon product links are affiliate links.

Tagi