1 / 2
8311 Yuanley 6 Port 2.5G Switch WAS-110 SFP Module Cooler — zdjęcie 1
1 / 2

8311 Yuanley 6 Port 2.5G Switch WAS-110 SFP Module Cooler

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Keep power level 3 SFP modules cool in the Yuanley Switch

Ocena
0 / 5
Polubienia
2
Pobrania
15
Wydruki
0
Wyświetlenia
1717
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Computers
Licencja
Creative Commons — Attribution

Power level 3 SFP modules like the WAS-110 consume ~3W and benefit from active cool around the heatsink. This shroud uses a 3010 axial or blower fan to move airflow above both cages.

 

3010 Blower Fan Duct

BOM

  • 1x: 3010 12V blower fan
    • I'm using a quieter 24V fan
  • ~1ft: 24 AWG silicone wire
  • 2x: M3 x 6 FHCS
  • 2x: M3 x 4 x 5 heatset inserts (the “Voron ones”)
  • Printed parts:
    • 3010 Blower Fan Duct

 

Assembly

  1. Preparing the Switch
  • Cut the front top case above the SFP cages
  • Drill and chamfer M3 holes to mount the duct
  • Use a hole saw to drill a 1" hole for the fan intake

 

     2. Electronics

  • Remove the PCB from the bottom case
  • Solder two wires to the legs of the DC power jack (the inside should be positive but may vary)
  • Attach those wires to the fan leads

 

     3. Fan Duct

  • Add the M3 heatsets in the duct
  • Place the fan in the duct and screw it to the top case

 

     4. Optional 8311 Mod

  • Want to give your switch some 8311 flare? Print one of the labels to replace the Yuanley faceplate.

 

3010 Axial Fan Duct

BOM

  • 1x: 3010 12V fan
  • ~1ft: 24 AWG silicone wire
  • 2x: M3 x 12 FHCS
  • 1x: M3 x 4 x 5 heatset inserts (the “Voron ones”)
  • Printed parts:
    • 1x: Fan Duct
    • 1x: Fan Mount

 

Assembly

  1. Preparing the switch
  • Cut the front top case above the SFP cages
  • Cut a 30mm square hole on the right top case for the fan intake
  • Drill and chamfer an M3 hole to mount the duct

 

     2. Electronics

  • Remove the PCB from the bottom case
  • Solder two wires to the legs of the DC power jack (the inside should be positive but may vary)
  • Attach those wires to the fan leads

 

     3. Fan Duct

  • Add the M3 heatset and place the shroud above the cages
  • Slide the top case back on with 3 screws
  • Reuse one of the original Phillips #2 screws to hold the shroud
  • Place the mount on the fan and hold it with the M3 x 12 FHCS

 

     4. Optional 8311 Mod

  • Want to give your switch some 8311 flare? Print one of the labels to replace the Yuanley faceplate.

Tagi