1 / 6
Inlet kit for various boxes - fits Enders Alubox Toronto 63l — zdjęcie 1
1 / 6

Inlet kit for various boxes - fits Enders Alubox Toronto 63l

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Corner brackets to build a robust but lightweight inlet for the Enders Alubox Toronto 63l.

Ocena
0 / 5
Polubienia
0
Pobrania
6
Wydruki
0
Wyświetlenia
76
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Organizers
Licencja
Creative Commons — Attribution — Noncommercial

This is a set of top and bottom brackets to build a robust but lightweight inlet for the Enders Alubox Toronto 63l. With the provided measures, you can fit three inlets into the box.

You need:

  • 4 of both models 
    • bracket_v2 has screw holes in the top-to-bottom profile mounts
      Because of the print orientation and depending of layer strength, this piece is prone to break during riveting. So I added two vertical M3 screws reinforcing it.
      You may not need it, if your layer cohersion is strong. Test it out with a sample.
  • 8x M3x8mm screws
  • 20x blind rivet 4x8mm
  • 3mm & 4mm drills
  • 2x 20mm webbing straps
  • [only for reinforced v2] 16x M3x16mm screws
  • aluminium extrusion profiles 19,5x11,5mm with following lengths: 
    • 2x 44,5cm
    • 2x 24cm
    • 4x 6,5cm 
    • 3mm aluminium dibond plate measuring 52cm x 32,5cm

The last profile length can be changed for various inlet heights. Target inlet height minus 4,5cm = profile length.

Print the brackets with the profile mounts pointing up-&sideways.  Support the plate groove edges and screw holes in the bottom bracket. For easier removal, use organic support only from the print bed. The top brackets requires support under the profile mounts.
[Only for reinforced v2] Put the M3x16mm screws into the weaker upper bracket profile mounts to reinforce them against breaking on riveting.

You need to round the corners of the bottom plate. Use the inner curve of the bottom bracket as a guide, draw a cutting line for each corner and cut the dibond with a pair of metal scissors, jigsaw or similar tool. It does not need to be 100% perfect, as the cut is covered by the bracket.
Use a deburrer or file to soften the plate edges, as they might be sharp from sawing.

Use the bracket to mark the hole locations on the profiles. Drill holes on one side of each end.
Stick the top brackets in the profiles and rivet them together, but wait with the bottom brackets until you fitted the bottom plate. Its easier to jiggle them around while loose. When the plate fits, rivet the bottom brackets as well. Imperfect alignments of profile & bracket holes can be corrected after a dry assembly by drilling into the bracket through the profile hole.

Now drill the holes through the bottom bracket screw holes and the dibond plate, and fix the plate sturdy to the brackets with the screws and nuts. It is not necessary to tighten the screws extensively. The screws go in from underneath and won't stick out from the bottom bracket.

In a perfect world, you use a heated blade and rod to cut the webbing and punch the rivet holes into it. It is also possible to use scissors and a hole punch, but maybe use a lighter to - slightly - melt the cutting edges in order to prevent loose threads. Mark and drill 4mm holes 7cm from the 24cm profile ends and rivet the webbing straps on as handles.

Material sources for Germany

Tagi