1 / 10
VR Transpoint Sp/Spa/Spar wood transport stake car H0 1:87 — zdjęcie 1
1 / 10

VR Transpoint Sp/Spa/Spar wood transport stake car H0 1:87

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

a rough model based on the finnish national railways stake cars found all over the national network

Ocena
0 / 5
Polubienia
22
Pobrania
220
Wydruki
0
Wyświetlenia
1065
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Vehicles
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

About the prototype

The Sp series of stake cars were built in the turn of the decade between the 80s and 90s, to work alongside with the older Ocpp type. The main difference being the newer Sp type having the ability to move the 10 stakes individually to accommodate different lengths of lumber while also easing up the loading and unloading processes 1. The Sp type has nowadays completely replaced the older Ocpp type. Most of them being scrapped or living on as converted Sp type wagons (Sps) 2. 

 

 

source 3.   
 SpSpsSpa, Spar
Tare (t)21,3/2222,222,9/22,3
Load (t)58,5/5857,557,0/57,5
Cargo volume   
Length (m)19,5019,5019,50
Width (m)2,80/2,852,852,85
Stake height (m)2,55/2,652,692,69
    
Coupling type   
 Screw linkSA3 automatic 
Sp, Spsyesno 
Spanoyes 
SparyesyesScrew/SA3



 

Design

A little shower thought that spiraled into a little pet project. The design is 98% fully 3D printable, with only the wheelsets, couplers and 2 M3x8 screws as external components. The design was tested using R1 curves and turnouts (360mm/30°) with a load at full speed

The coupler sockets are made according to the NEM362 standard and are designed to work with märklin relex couplers or standard hook and loop couplers. 
 
Note: The model has 9 stakes instead of 10 like the prototype, idk how i didn't  catch that discrepancy or if it was a conscious decision. Either way, it still looks close enough despite that. Heck i only noticed it as i was writing this, somehow. 

Recommended material and colour schemes

 

PLA or PETG, PLA provides better detail but is harder to post-process. PETG is easier to sand and work with but tends to ooze more than PLA.

The following are colour schemes that are currently in use:

Cyan, sky blue/oxide red, reddish brown

Light grey/oxide red, reddish brown

Grey/luminous green

Printing

 Supports, refer to the imageslayerheight
Bufferspaint<0,20
Stakenoany
Chassispaintany
Bogeypaint<0,25
Coupler pocketbuildplate onlyany
Bulkheadnoany
 Brim recommended for adhesion.  painted side towards the bed 
Chassis


or


 

bogey

 

buffer and coupler pocket


Assembly

Needed components:

2x M3x8
H0 wheelsets of your preference
Märklin relex couplers or equivalent hook and loop coupling
Printed parts (9x stakes, 4x buffers, 2x bogeys, 2x couipler pockets, 2x bulkheads)


Assembly is simple, follow the coloured and numbered arrows in order. The letter "C" is a stand in for a coupler. At step 5, add a tiny drop of cyanoacrylate glue to secure the buffers.

 


 

 

 

 


Happy printing! Don't forget to post a make!
 

Photo credit: 
Teemu Saukkonen ( https://vaunut.org/kuva/154716?tag0=11%7CSp%7C )
Antti Kukkonen (  https://vaunut.org/kuva/146792?tag0=11%7CSp%7C  )

Sources:

  1. https://veturitalli.fi/viewtopic.php?t=2017
  2. https://veturitalli.fi/viewtopic.php?t=1558
  3. https://www.vrtranspoint.fi/fi/vr-transpoint/asiakkaan-opas/kalusto/rautatiekalusto/kotimaan-liikenteen-vaunut/avovaunut/raakapuuvaunu/raakapuuvaunut-sp-sps-spa-spar/

     

Tagi