1 / 6
[ChiShui] RedWaters - Magnetic Gunstock for Quest 2 — zdjęcie 1
1 / 6

[ChiShui] RedWaters - Magnetic Gunstock for Quest 2

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Designed and tested mainly for H3VR, proportions are based on HK416 so works best with anything that looks like an AR

Ocena
0 / 5
Polubienia
39
Pobrania
77
Wydruki
0
Wyświetlenia
1257
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial

21/11/2024

Changed angels on the right controller mount to make aiming easier

=========================

This thing improved my accuracy quite a bit with rifles and such.

Everything is printed with a 0.6mm nozzle with PETG, the spring should have only 1 wall

This is an iteration of my last attempt (more or less failed folding&extending stock in the back)

 at making a magnetic stock for Quest 2, all of this happened within a week so bear with me if there are any bugs I overlooked, point them out for me and I'll get it fixed.

 

So anyway, this thing is inspired by Sanlaki, Teque5 and the many others who had done this before me. Wanted to do my own because I can, and also because I wanted more out of it.

 

 

Stuff you'll need off of Amazon or your average local supplier (I just copied the links from Amazon, so I suppose they are not affiliated):

 

Everything is Printable (pun intended) on a Prusa Mini (18*18*18) so this should be alright for everyone. I printed everything in PETG but should work with PLA as well, except for the spring, it might be a bad idea to do so

You should start by picking one of the 3 sets to start printing, if your print bed can fit them all, I would like to let you know that I envy you.

Buttstock:

Controller Adapters:

Tube Covers:

Before we go over any details, here are a couple of pictures of what the thing is supposed to look like both assembled and exploded, with screw type and amount marked.

 

The assembly is quite simple really, I'll cover it in the order of Controller, Barrel, Stock and Padding ranked in how important it is for it to work. 

ALL unused screw holes are possible attach points for future upgrades, pump action module, bolt action module, lever action module and trigger discipline module are in consideration, development has not started yet.

 

  • When in doubt, refer back to the layout images above, or ask
  • All the bolts with a range, like 20~25mm, the lower end is the minimum you'll need to get to the other end, and the higher end is how long you can go without possibly getting in the way of smth else. It's roughly the same for parts that have a range requirement for their quantity, I would suggest doing them all

 

Controller:

  • [2] M5 20~25mm Countersunk bolts
  • [2] 32*8mm 90lb magnets
  1. Place the magnets in
  2. Place the nut in on the bottom, and then secure it with a M5 20mm countersunk bolt (this should be a machine screw, instead of those that came with it) from the other side
  3. Press in both ends of the thing and slide it into the tracking ring (as shown on the right)

 

 

 

 

 

They will stay in there pretty well since it's modelled off of a scan of those controllers. When in need of taking them off, press in the shorter side with the magnets (counterintuitive I know) and it can be slid out.

To take out:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Barrel Cover:

  • [8~14] M3 10~16mm bolts
  • [4] M3 20~25mm bolts (optional, for the Sling Connector)
  • [12~18] M3 nuts

(technically you only need the back piece to make this functional, but it's nice to have rolling locks on the whole length, note that longer mags with roll locks will partially obstruct radar, might need to twist the left controller to the left or back to see)

  1. Slide in and screw the back piece onto the pipe, 
  2. doesn't have to be tight, finger tight is more than good enough, the threads in the print are just there to hold things for you while assembling
  3. Do the same with the front piece and roughly align them
  4. Place the m3 nuts in place (see picture on the right). If you encounter trouble pushing them in, or have trouble pulling them in with a bolt on the other side, try half-nutting them on a long screw and wiggling them in from the bottom (the side on the picture). I recommend doing them all, but those in the red box are the bare minimum for it to be secured, those in the yellow box are for the sling connector, can be left out if you don't want a sling (it's very nice to have)
  5. Place the Mid Cover and the Sling Connector on and start screwing them in, power tools help a lot in this project. Longer bolts are for the Sling Connector
  6. Careful not to overtighten things, finger tight is plenty and prints squashed too much could crack

 

Stock:

  • [4] M3 25~40mm bolts (25~30mm recommended)
  • [4] M3 40mm bolts
  • [1] M3 25~30mm bolt (30mm recommended)
  • [11~13] M3 nuts
  • [2] M3 washers
  • [2] M3 23~30mm bolt (optional, 25mm recommended)

This is a 3 stage adjustable stock. You'll need to make a choice before building it, the slider has 2 ways of returning to where it's supposed to be while in action. A printed spring (recommended), or with rubberbands as a backup option in case the printable spring doesn't work for you, more of this will be covered in the assembly steps.

Some of these steps will be shown on a previous version, but the assembly process and the general silhouette of the parts are the same.

 

  1. Slide the stock shell onto the stock base 

 

 

 

 

 

 

     2. Slide in the slider

 

 

 

 

 

 

 

     3. Drop in the pin through the hole in the slider, it should align if you push them both against opposite end

 

 

 

 

 

 

     4. Push a M3 30mm bolt with a nut and a washer near the cup through the hole on the side, this is the pin for your pin. 

Then put another washer and another 2 nuts on the other side, making sure there is a gap about 0.5mm (just leave a visible small gap) between the washer and the wall of the stock shell, after that, threadlock or superglue the nuts in.

Whole thing is shown on the right.

Nuts are marked red and washers are marked blue.

 

 

 

 

 

     5. Slide the spring in through the opening on the top back of the stock shell (the rubberband method will be covered later)

 

 

 

 

 

 

 

     6. Push the other belt connector, with holes that align with the end of the stock, and the stock bottom onto the stock shell, there's an extrusion there that will go into the slot you just put the spring into. Then screw it down with 4 M3 40mm bolts, remember to push nuts in on the other side first

 

 

 

     7. Now your stock should be adjustable, try it by pushing the slider back and move it around, you should see the pin being lifted by the slider when you're doing that. If in doubt, check the GIF for reference

 

 

 

 

 

     8. This is optional, but you can screw the stock bottom into the front bottom of the stock shell to get a bit more stability, tho it's barely noticeable and more for the peace of mind

 

 

 

 

 

     9. This is optional, if the spring doesn't work for you, or that you just don't like them, here is how you set up the same system with rubber bands. 

Bolts are needed at these 2 positions, need to be at least: 2*RubberBandWidth+BoltLengthYou UsedForPin

I used 40mm for the ease of putting together, they need nuts on each side and washers for the one that connects to the slider (one on the right)

 

     10. This is optional for the whole build, not optional for the rubberband system. Wrap rubber bands on and you are good to go, works fine with just one but looks better with 2

 

 

 

 

 

 

     11. Screw the stock base into the back cover with 4 M3 30mm bolts, remember to put nuts in on the other side

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Padding:

[Enough]EVA foam

     1. Cut to the size, you can slice a thin piece from the stock bottom in your slicer and print that out as a template. Cut as many as you feel is comfortable, I don't really feel the difference between 10mm and 20mm, but the extra distance I can push down is nice

 

 

 

     2. Stick them together, in this case, I used the self adhesive on the back of the thing. I don't know what glue you should use with EVA but it's definitely not super glue. Plain old double-sided tape should be just fine

 

 

 

 

     3. Stick it to the bottom of your stock and be done with it

 

 

 

 

 

 

 

 

Congratulations, you made it to the end, I have no idea if you built it or not so please leave a make if you can, I would love to see those.

Blend file is attached for easy remixes, most things have backups hidden in the scene so you can just unhide all the collections and then hit it with Alt+H to work with those of your choosing.

Tagi