Lampshade for "Hokan" LED gooseneck lamps
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A lampshade to fit "Hokan" brand LED gooseneck lamps. Available in 15mm and 25mm depths.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 7
- Wydruki
- 0
- Wyświetlenia
- 86
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Home Decor
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
I have a few of these gooseneck LED light bar lamps around the house, currently being sold under the brand Hokone. Their identifying characteristic is a distinct "ducktail" shape under where the gooseneck meets the lamp body. They work pretty well for task lighting, but I found they give off a bit too much glare to the sides when used as a reading lamp. I designed this lampshade that clips around the body of the lamp and keeps the glare out of my eyes.
Designed to print with a .4mm nozzle. The model has a .84mm wall thickness and should glow warmly when printed with white filament. It also looks good, if a little gaudier, printed in translucent filament with a bit of "fuzzy skin" effect enabled. Or maybe you could use translucent colored filament and put a light coat of white paint on the inside for a classic "bankers' lamp" look.
The model is provided in a shallower 15mm and deeper 25mm depth, as measured from the bottom of the lamp lens. It is designed to print in two pieces which fit around the body of the lamp and are joined with four short pegs of filament (glue optional.) I ream the holes by hand with a a size #52 bit and I find this gives a good friction fit.
The model files arrange the two halves to print together, supporting each other. Additionally, I included models for the the unsplit versions, if you have a larger format printer, but you are on your own as to how to orient and support it.
RECOMMENDED PRINT SETTINGS:
Must use Arachne / variable width walls, and an outside brim (turn off the inside brim, as it will go into the peg holes.)
"Outside walls first" may give a better outside surface with less ghosting/artifacts, at the possible expense of the less-visible interior surface.
See attached figure for recommended supports. There is a modeled-in support strip connecting the two halves together to give them stability while printing. Besides this, it will need supports under the ends of the inner lip that fits around the lamp, as well as under the outer perimeter. It should not need support for the logo or the thin "straps," and definitely make sure it does not put any supports into the peg joining holes.
Pay attention to seam location and encourage the slicer to put the seam on the inside surface/corners.
With a thin shell, there is not much material per layer, so many slicers will slow down some layers to make sure layer times are not too short. These changes in speed may lead to irregularities in surface finish especially with transparent or shiny filaments. Slowing your max speed down to be more constant (or printing multiple copies so that layer times are not too short) may improve surface finish.
OTHER NOTES:
This was a design exercise in modeling a smooth, curving object closely enough to fit it mechanically, and then smoothly extending its curvature into my desired shape. What I found out is that you can build up such a shape up by using a combination of lofts with tangent constraints, offset/extend faces, split body, etc. but after a number of successive such operations, I find Fusion starts to actively hate you. The NURBS surfaces thus generated must just have an enormous number of control points. One fillet in particular takes twelve minutes to compute, and propagating a small dimensional change through the timeline takes hours of babysitting. So this exercise has led me to wonder if there is software that does better with manipulating curved surfaces in a parametric way....