1 / 7
Harbor Freight 2HP Dust Collector outlet port with downward curve (or flip it for upward curve) v1.0 — zdjęcie 1
1 / 7

Harbor Freight 2HP Dust Collector outlet port with downward curve (or flip it for upward curve) v1.0

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Drop-in replacement for original, but with a downward curve (or upward curve)

Ocena
0 / 5
Polubienia
6
Wydruki
0
Wyświetlenia
240
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Tools

This can be helpful in converting your Harbor Freight 2HP Dust Collector from a 1-stage to a 2-stage unit, which is what I did by way of adding a *Super Dust Deputy 4/5. If you're limited on ceiling height like I was in my basement, this design adjustment was needful for me.

This is a replacement for the original outlet port of a Harbor Freight 2HP Dust Collector, but with a downward curve (or flip it for upward curve instead). I think it does need bolts that are a bit longer  than the original ones.

  • Save and reuse your stock rubber gasket.
  • Print as oriented.
  • Prints without need of supports.
  • Recommended: PLA or PETG (I printed mine in Prusament PLA Galaxy Black).
  • Will print stronger (and possibly quicker) if you increase number of perimeter walls so it prints solid, or mostly solid, at least on the chute part.
  • For the base part that will need infill, I recommend a high infill percentage, say 40%-50%. When you crank down on the bolts, don't go crazy. Remember there is (or should be) a stock rubber gasket under there, so you don't need tons of torque, and you don't want to crush the printed plastic.
  • Before installing, consider slapping a coat of polyurethane (or epoxy) on the inside of the part to make sure the extremely high air pressure does not force fine dust to exude through the plastic strands of the print.

Note: I am also working on one like this, but with a left/right bend instead of up/down. If you need that one, check back soon, or even drop me a message.

Change Log:

  • Dec. 12, 2024 - updated with thicker transition from base to port, to help prevent splitting (delamination) at layer lines. 
  • Nov. 30, 2024 - updated with thicker base, to help resist deforming when installed. Also revised recommended infill from 30%-50% up to 40%-50%.
  • Nov. 26, 2024 - initial upload

Also see (below) my related models used in my conversion from 1-stage to 2-stage on my dust collection:

Dust Collector Top Adapter 6" to 5" - turn Harbor Freight 2HP DC into 2-Stage, using Super Dust Deputy 4/5 - https://www.printables.com/model/1071457-dust-collector-top-adapter-6-to-5-turn-harbor-frei 

Dust Collection Adapter (from Harbor Freight 2HP DC 2-into-1 "Y" to Super Dust Deputy 4/5's inlet port — 5" to 5" - https://www.printables.com/model/1071489-dust-collection-adapter-from-harbor-freight-2hp-dc 

Dust Splice Coupler Adapter - from 4" PVC to 4" Dust Hose (based on POWERTEC 70123 O.D. Splice, 4", Black) - https://www.printables.com/model/1077981-dust-splice-coupler-adapter-from-4-pvc-to-4-dust-h 

Dust Splice Coupler Adapter - from 4" Flex Hose to 4" Flex Hose - https://www.printables.com/model/1077997-dust-splice-coupler-adapter-from-4-flex-hose-to-4 

*Amazon links are affiliate links.