1 / 4
Double shear, top bearing support for A B motors for Chaotic Labs CNC kit — zdjęcie 1
1 / 4

Double shear, top bearing support for A B motors for Chaotic Labs CNC kit

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Double shear, top bearing support for A & B motors for the Chaotic labs CNC AB motor mounts for Voron 2.4.

Ocena
0 / 5
Polubienia
13
Pobrania
65
Wydruki
0
Wyświetlenia
1552
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
GNU General Public License v3.0

This mod enables a double shear, top bearing motor support for the AB motors specifically for the Chaotic labs CNC kit.

It is a remix of the excellent work done by Vitali and adapted for precise fitment on the CL CNC kit.

Print settings:

As you want maximum strength, I printed the model with the following settings:

  1. 20 walls
  2. 1 wall top and bottom surface
  3. Inner Outer Inner mode in Orca slicer. Alternatively print outer to inner. This is because you want precision in the external wall and only these two modes can “guarantee” no deformation of the external perimeters due to material overflow from the internal perimeters
  4. 0.2 LH / 0.4mm line width / 0.4 mm nozzle

I printed it using ASA CF and specifically the Bambu Labs ASA CF filament on my Voron 2.4. 

Make sure your printer is well calibrated. A tolerance of 0.1mm or less is expected for the parts to fit precisely and not be too tight or too loose. If the parts are slightly too tight you can sand the bearing holder slightly to get them to fit. Please wear a mask if you do so, with CF filled filaments.

Please note, the model has been adjusted to be a very tight fit and specifically adjusted for the shrinkage ratio of ASA CF. If using a different material you may need to adjust your shrinkage compensation in the slicer to get a precise fit.

What you'll need

I have included 3 versions of the top mount, with slightly varying thickness. Which one to use will depend on how deep the bolt threads in your stepper drivers are. 

For the LDO motor I used the 6mm thick version together with M3 x 30 bolts.

Print 2x of the motor mounts and 2x of the bearing holders. The bearing holders should twist lock on the mounts.

Motors:

You'll need a long shaft motor to utilize this mod. Shaft length of at least 46mm is required. I used these motors: LDO Stepper Motor 42STH48-2504AH(S46)

Bearings:

You'll need 2 flanged bearings, the same type as the standard ones used in the Voron gantry. I used a pair of west 3d hybrid ceramic ones (Berserker F695-2RS) which I had ordered as spares.

Fitting:

Place the bearing in the motor mount. There should be NO PLAY in the bearing against the motor mount. Add the bearing holder and twist to lock. If there is play, adjust your flow rate accordingly. If it is too tight, adjust your shrinkage compensation in the slicer.

Belt tension:

I adjusted my GT2 belt tension to 190hz over 150mm. It might be easier to measure the frequency if you target 200mm, in which case, use 140hz.

Absolute max tension is 218hz over 150mm / 163hz over 200mm.

Taken from this calculator here: http://lukeslab.info/en/belt-tension-guide

Results:

My Y shaper increased from approx. 4500mm/sec2 accel to approx 5500-6000mm/sec2.

Optional items:

In my specific kit (MPX 2.4 350) I needed to slightly modify the Y end stop retainer as it would not fit together with the top bearing mount. If you are using senseless homing or an alternative Y end stop location, this is not needed.

Tagi