1 / 4
Epsilon V2 Airflow Noctua Edition (For Asus RTX4060LP) — zdjęcie 1
1 / 4

Epsilon V2 Airflow Noctua Edition (For Asus RTX4060LP)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

An extended version of the Epsilon v2 to accommodate a Asus RTX4060LP and extra fans

Ocena
0 / 5
Polubienia
8
Pobrania
43
Wydruki
0
Wyświetlenia
539
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Computers
Licencja
Creative Commons — Attribution — Noncommercial

I loved the original Epsilon V2, but it wasnt long enough to fit an Asus 4060LP. The Asus card is slightly longer than the A2000 or the Gigabyte 4060LP. 

I also wanted to make a more porous airflow style configuration of this case. 

This case has has the front section extended 20mm to accommodate the longer card. After testing, it was pretty clear that there was an issue of getting the hot air out of the case from the GFX card side. I went and modified the bottom panel, creating 2 large rectangular openings, and lengthened the height of the feet to 30mm so that a 15mm fan could be mounted on the bottom of the case to help pull the hot air out from the gfx card and CPU cooler as well. The original side panels were modified to create a fuller mesh panel, and the top panel had mesh added as well. 

The spine has also been modified to create additional clearance between its self and the PCIE riser cable (especially if you have a Z or X series motherboard that has armor or is just has a thicker PCB in general.)

I would also like to recommend that PLA should only be used for the following panels:

Front, GPU Side, CPU Side, Top, and Rear.

DO NOT USE PLA FOR THE BOTTOM PANEL OR THE SPINE. THESE PANELS WILL WARP AND MAY CAUSE ISSUES WITH THE GPU RISER. Print the Spine and Bottom panel in PETG, ASA or ABS. 

Hardware I used in this build found here:

Motherboard - https://www.gigabyte.com/Motherboard/Z690I-AORUS-ULTRA-LITE-DDR4-rev-10 

CPU - https://www.amazon.com/Intel-i5-12600K-Desktop-Processor-Unlocked/dp/B09FX4D72T/ref=sr_1_2?sr=8-2

CPU Cooler - https://www.amazon.com/quiet-BK034-Pure-Rock-Intel/dp/B0BNYVJNL9 

Noctua CPU fan - https://www.amazon.com/Noctua-NF-A9-PWM-Premium-Cooling/dp/B00RUZ059O/ref=sr_1_1?s=electronics&sr=1-1 

Memory - https://www.amazon.com/Corsair-VENGEANCE-3200MHz-Compatible-Computer/dp/B07RW6Z692/ref=sr_1_4?sr=8-4

PSU - https://www.amazon.com/T-F-SKYWINDINTL-Modular-100-240V-Mainboard-Desktop/dp/B0C3TW95T3/ref=sr_1_4?sr=8-4 

GFX Card - https://www.newegg.com/asus-rtx4060-o8g-lp-brk-nvidia-geforce-rtx-4060-8gb-gddr6/p/N82E16814126723 

PCIE Riser - https://www.amazon.com/gp/product/B0CBVSFZS2/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8 

Noctua 40mm Fans - https://www.amazon.com/Noctua-NF-A4x10-PWM-4-Pin-Premium/dp/B07DXRNYNX/ref=sr_1_5?s=electronics&sr=1-5 

Noctua 120mm slim fan - https://www.amazon.com/Noctua-NF-A12x15-FLX-Premium-Quality-Quiet/dp/B071J8BZ8S/ref=sr_1_3?s=electronics&sr=1-3 

Update #9 - 12/30/2024

v2.0 has been uploaded

Changes include:

 - Re-mesh of bottom panel. increase of Mesh pattern and revised placement of the 120mm fan mounting.

 

Update #8 - 12/29/2024

v1.9 has been uploaded

Changes Include:

 - Rear panel update. Addition of a second smaller mesh panel above the IO shield. Slicer shows a graphical error, but the panel prints successfully. This will be remedied in a later update

 

 

Update #7 - 12/28/2024

v1.8 has been uploaded

Changes include:

 - Addition of cable Management anchor slots to the front edge of thew spine to hemp keep PSU cables as close to the spine as possible to mitigate distortion of the front panel becauser of excess pressure being applied by PSU cables.

 

Update #6 - 12/25/2024 

v1.7 has been uploaded

Changes include:

 - GPU panel added and modified with an intake cutout and split into separate bodies for easier multicolor printing.

Update #5 - 12/25/2024

V1.6 has been uploaded

Changes include:

 - Front panel has been split into two separate bodies (One for the main tan parts, one for the brown mesh). This ensures that no infill in the tan section will contain brown filament.

 

Update #4 - 12/24/2024

V1.5 Has been Uploaded

Changes include:

 - Split CPU Side panel into two separate components in Fusion 360. This eliminates Bleed through of the Dark brown into the tan area where the CPU Cooler fan cutout is located.

 - Positioning of the CPU Cooler opening in the side panel has been adjusted to align better with the CPU Gap Hider that was added in v1.3

Update #3 - 12/23/2024

v1.3 has been uploaded

Changes Include:

 - Addition ofCPU Fan intake hole in CPU side Panel

 - Addition of CPU fan gap hider (to mitigate ugly gap between CPU fan and the hole in the side panel

 

Update #2 - 12/22/2024

v1.1 has been uploaded

Changes Include:

 - Repositioning of the front panel dual 40mm fans

 - Adding text to the front panel

 

Update #1 -  12/22/2024 

v1.0 has been uploaded

Changes include:

Mesh added to the Back panel (Rear Power Button only)

 

 

 

 

 

 

 

 

Tagi