Ski and Poles Clip / Ski and Poles Holder
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Slightly over engineered Ski and Pole Clip/Holder/Carrier.
- Ocena
- 0 / 5
- Polubienia
- 35
- Pobrania
- 192
- Wydruki
- 0
- Wyświetlenia
- 1746
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Winter Sports
- Licencja
- Creative Commons — Attribution — Noncommercial
Parametrized Ski Clip to transport skis and poles together, slightly over engineered ;-)
Completely parametrized, therefore works for a wide variability of skis and poles, even elliptic poles and asymmetric skis (different width/thickness in front and behind binding).
There are also dampers to be printed with TPU to prevent slipping and protect the ski.
The two additional (small) clips are for additional fixation, normally not necessary, but might be handy for transport in vehicles with many skies lying around.
Normally only the main parameters are necessary to be adapted (see below), for special cases or customization the secondary parameters might be helpful.
If you have round poles and not elliptic ones, just use the same diameter for dia1 and dia2.
Finally, there is a text emboss to either clip to label them top and bottom, or put your first and last name on it, to know which clip goes where.
Material & Print parameters:
ABS works well, I prefer CF-Nylon though. With CF-Nylon the strength is enough to even carry the skis holding the poles.
PLA did not work for me, not strong enough and too brittle.
TPU for the dampers. You can also export the whole model (clip and dampers) and print as is all in ABS.
No special print parameters necessary, except potentially a brim or a raft, depending on bed adhesion.
Main parameters:
| Parameter | Explanation |
|---|---|
| ski_width_top | Width of the ski above the binding |
| ski_width_bottom | Width of the ski below the binding |
| ski_thickness_top | Thickness of the two skies together (as is, do not compress), above the binding |
| ski_thickness_bottom | Thickness of the two skies together (as is, do not compress), below the binding |
| pole_dia1_top | diameter 1 (parallel to ski surface for an ellipse) of pole at top height |
| pole_dia2_top | diameter 2 (perpendicular to ski surface for an ellipse) of pole at top height |
| pole_dia1_bottom | same as for top |
| pole_dia2_bottom | same as for top |
Secondary parameters:
| Parameter | Explanation |
|---|---|
| compression | a factor for compression of the skis with the clip. Influences the snapper resistance/strength. Can also be used to tune for the material used (stiffness). |
| tolerance | spacing between different parts, overall “snugness” e.g. lateral distance between damper-clip and many others. |
| holder_thickness | thickness of the holder |
| holder_height | height of the holder |
| angular_overlap | how many degrees above 180 for the clips that hold the poles |
| distance_ski_pole_top | Distance between ski edge and center of pole at top |
| distance_ski_pole_bottom | Distance between ski edge and center of pole at bottom |
| distance_between_poles_top | Distance between the two poles at top |
| distance_between_poles_bottom | Distance between the two poles at bottom |
| damper_thickness | as the name says. Set to 0.01 for no damper. If you don't want holes, also set hole_diameter and hole_tolerance to 0.01 (0 does not work, 0.01 keeps the models integrity) |
Inspiration by https://www.printables.com/model/755625-ski-carry-clips-v3