MKS Gen V1.4 2020 enclosure case with 40mm fan
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
MKS Gen V1.4 2020 enclosure case with 40mm fan
- Ocena
- 0 / 5
- Polubienia
- 2
- Pobrania
- 14
- Wydruki
- 0
- Wyświetlenia
- 97
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial
I retired a project 3D printer, but the board was still good. Flashed it with Klipper to use as a secondary MCU for another printer. The target printer was going to lose the screen as it was not compatible with Klipper. Salvaged the 2004 LCD screen for basic functions.
Took the model available from Grabcad.com and modeled this enclosure case around it. I added a hole on the top for access to reset, and holes along the sides for connections. There was one alignment difference between the model, and my board, so I extended a hole to make sure it worked with both.
There are 3 bottoms available with 2 of them having 60mm offset tabs. For my purpose I will be using Bottom60x60FrontRight.stl as the power will be coming in off the right side. Bottom60x60FrontLeft.stl is for mounting to the front left of a 2020 frame. I have another MKS board that will be coming available, and this will be used a test/development platform, so I made a bottom with no tabs.
The Tabs can be used to mount above or below the 2020 frame and depending on the use case these could be used in a vertical mount(untested).
Hardware Required:
4 x M3 x 30mm for assembling top and bottom
4 x M3 Nuts or Nylock nuts
2-4 x M3 16 or 20 mm for mounting the fan (inside or out)
2-4 x M3 Nylock nuts mounting the fan (avoid rattling loose)
4-5 x M5 x 10mm (mounting to 2020 frame)
4-5 x M5 Hammer nuts (or similar) to mount to frame
**M4 could be used to mount to 2020, but washers maybe required for fit.
I printed mine in PLA as it will not be in an enclosure, nor will it be near the bed. Print settings were 3 walls, 4 top/bottoms, 20% infill, and 0.4 nozzle.
Install:
I recommend making sure the M3 screws pass through the holes in the top and bottom parts freely without having to cutting threads. I used a drill bit to clean the holes up. M3 nuts were pushed in cutouts on the bottom. I dry fit the top and bottom without the board to use the M3 screws pull the nuts all the way in. I then used a fan cover, 2 x M3 x 20 screws, and 2 Nylock nut to mount the Noctua 24V 40mm fan to the top part.
Update May 12/2025
I did end up installing this as is, but found installing the 4 screws through the lid, and the board to be very difficult. I added some additional files to make things easier. The TopShortPosts allow the board to be mounted with short screws. I used 2 x 20 mm to mount the board, then 2 x 30mm on the opposite corners. There are parts called TopBoardClearanceSpacer, and TopRoundSpacer these are used on the corners that use the 30mm screws to get close to the board.
Additionally, 2 bottom parts were designed for distance of 40mm on both sides. I found that the 60mm had too much room for cables, and added a bit of sag to the part.