1 / 17
BigTreeTech BTT Pi2 Case w/30 or 40mm Fan and Optional Din Mount or Dovetail Mount — zdjęcie 1
1 / 17

BigTreeTech BTT Pi2 Case w/30 or 40mm Fan and Optional Din Mount or Dovetail Mount

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

BigTreeTech BTT Pi2 Case w/30 or 40mm Fan and Optional Din Mount or Dovetail Mount

Ocena
0 / 5
Polubienia
6
Pobrania
64
Wydruki
0
Wyświetlenia
453
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial

This is a BTT Pi2 case designed from scratch based on the model supplied for the BTT Pi 2.

The following files were created:

BottomBlank.stl
BottomHoles.stl
BTTPi2DinMount.stl
DoveTail4mmSpacerX2.stl
Top30mmInside.stl
Top40mmOutside.stl
DoveTailCombo.stl

There is a choice of bottoms for the case depending on if it will be a mounted.  If this will just be sitting on a desk for a project the BottomBlack model should be fine with exception if there is a M.2 drive being mounted to the BTT Pi 2.  If an M.2 is being used, then BottomHoles should probably be used with some kind of standoff or spacers.  I have supplied 2 different spacers that could be scaled in the Z direction depending on the purpose.  

The second bottom is BottomHoles, and this could be used with one of the other files BTTPi2DinMount. Depending on if an M.2 drive is used the spacers are going to be recommended to allow extra space for air.  DoveTail4mmSpacerX2 files are supplied and could scaled in the Z direction. The other use for the BottomHoles is to be used with the Dove Tail mount supplied by: Josh Park 
https://www.printables.com/model/424711-orange-pi-3-lts-case-wall-mount-dovetail-style
The part required is Pi dovetail.3mf

I have supplied spacers to help with the M.2 ventilation DoveTail4mmSpacerX2. These can be scaled in the Z direction depending desired height. These will work with Din Mount and DoveTailCombo.

There are 2 top files supplied. I tried to include all possible holes for buttons, and pass-through connectors for the BTT Pi 2.  Not all these connections have been tested, but the housing for the connections plus 0.1 mm was used for spacing. The Top30mmInside is for mounting a 30 mm fan inside using M3 screws, and bolts (nylon, or nylock bolts are recommended). The other file is Top40mmOutside for mounting a 40 mm fan on the outside and screwing into the plastic.  A fan guard is recommended.

The BTT Pi 2 doesn't appear to have a dedicated fan port like the BTT Pi 1.2 but could be powered by GPIO header.  Make sure you keep within the boards power limits otherwise an external powered fan should be used.

Additional dovetail mount with holes in both directions DoveTailCombo.stl.  This allows for different positions and additional mounting screws if using spacers.

Print settings:

I recommend 3 walls 4 top/bottoms, and 20% infill.  The models shown were in PLA as I'll be using them mounted next to my 3D Printer.  If being used in an enclosure, or under a printer like Voron series ABS, ASA, or PETG will be better options.

Hardware:

4 x M3x20mm countersunk screws for mounting top and bottom parts together
3-4 x M3 countersunk screws with a length

The DIN Rail was made possible by the work from CrazyIvan359(@CrazyIvan359_329483) and their work on this model:

https://www.printables.com/model/254550-lrs-35-din-mount

Head there and check their work out.

Tagi