Flying Raijin Kunai / Minato Kunai
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Modeled after the weapon used by Minato Namikaze in the Naruto Series
- Ocena
- 5 / 5
- Polubienia
- 44
- Pobrania
- 736
- Wydruki
- 4
- Wyświetlenia
- 2322
- Oceny
- 3
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Cosplay & Costumes in general
- Licencja
- Creative Commons — Attribution — Share Alike
IF YOU ARE CONFUSED BY ALL MODELS READ THE END OF THE DESCRIPTION FOR ALL COMBINATIONS FOR PRINTING !!!
Some other models in Naruto Collection:
Kunai
Shuriken

Flying Raijin Kunai
Dimensions (total):
Length : 30.00 cm
Width : 9.80 cm
Height : 2.60 cm
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-= =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=

Blade :
Length (Total) : 19.78 cm
Width : 9.80 cm
Height : 1.40 cm
Length (Without Connector) : 16.20 cm
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-= =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=

Handle :
Length (Total) : 13.50 cm
Diameter (Grip): 2.60 cm
Length (Grip) : 8.30 cm
Ring Size : 4 cm
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-= =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
1.0 Kunai (One Part)
If you want to print whole kunai from one model this is what you need
1.1 Kunai With Seal.3mf

1.2 Kunai Without Seal.3mf

=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-= =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
2.0 Two Part Models
2.1 Top & Bottom Parts
If you want support-less printing you can use two files below
Gluing them after printing
Those two are quite big models with 100% size they might not fit on some printers with smaller build surface
2.1 Kunai Half With Seal.3mf

2.2 Kunai Half Without Seal.3mf

You can print one of each to have kunai with seal (writing) only on one side
If you don't want seal you can print 2.2 Kunai Half Without Seal.3mf twice
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-= =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
3.0 Blade & Handle
This version has a seamless joint with a tolerance of 0.1mm
You can download Blade 0.05mm.3mf if you prefer 0.05mm tolerance same for 0.15mm and 0.2mm
The blade is inserted into the handle




3.1 Blade.3mf


=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-= =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
There are two versions of the handle ( with & without seal )
Handle is optimized to be printed vertically ( ring part at the top )
Keep in mind seal might not be best on some printers if printed vertically ( check 3.3.1 & 3.3.2 below if you want to avoid this )
3.2.1 Handle With Seal.3mf


3.2.2 Handle Without Seal.3mf


You can use either 2.1 Handle With Seal.3mf OR 2.2 Handle Without Seal.3mf in combination with 2.1 Blade.3mf
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-= =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
There is third option for handle its mix of first and second method
Because of the seal it would be best to print those parts as on images below gluing two halfs afterward
3.3.1 Handle Half With Seal.3mf

3.3.2 Handle Half Without Seal.3mf

=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-= =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
In summary
You can print the whole kunai with or without a seal by printing:
With Seal Version
1.1 Kunai With Seal.3mf
OR2.1 Kunai Half With Seal.3mf + 2.2 Kunai Half Without Seal.3mf
OR3.1 Blade.3mf + 3.2.1 Handle With Seal.3mf
OR3.1 Blade.3mf + 3.3.1 Handle Half With Seal.3mf + 3.3.2 Handle Half Without Seal.3mf
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-= =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
Without Seal Version
1.2 Kunai Without Seal.3mf
OR2.2 Kunai Half Without Seal.3mf + 2.2 Kunai Half Without Seal.3mf (Same Model Twice)
OR3.1 Blade.3mf + 3.2.2 Handle Without Seal.3mf
OR3.1 Blade.3mf + 3.3.2 Handle Half Without Seal.3mf + 3.3.2 Handle Half Without Seal.3mf (Same Model Twice)