Qidi Q1 Pro - FumeVault v1 - internally mounted GAC and HEPA filter
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Internal mount dual filter, using the Qidi Q1 Pro auxiliary fan, activated carbon and a Roomba 800 series HEPA filter.
- Ocena
- 0 / 5
- Polubienia
- 18
- Pobrania
- 27
- Wydruki
- 0
- Wyświetlenia
- 688
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial — NoDerivatives
My take on a powerfull recirculating particle and fumes filter, intended for the Q1 pro.
Surely it can be used on other makes/models, I would definitely be interested to hear about if anyone tries!
While there are already a few neat and simple-to-make options out there, they mostly use the chamber fan. Since I want to keep the chamber fan function as is, and as i havent had any real use of the auxilliary fan, I thought to re-purpose it instead, as a powerfull slicer controlled filter solution.

Using the Irobot Roomba 800 series HEPA filter(dirt cheap), along with a printed basket containing granulated activated carbon, in my case bought at a pet store and meant for fish tank filters, makes for a costeffective solution.
Printing:
- All parts are designed to be printed face down on the build plate, to avoid using supports, get the nicest finish, and to make the print as strong as possible in the areas where it matters. The case will need supports on the sloping face of the HEPA filter intake, this surface will be covered by the trim piece.
- The carbon basket should be printed standing, bottom down, and its lid, top-face down.
- I recommend printing everything in ABS for temperature resistance, the case and backplates especially as they need to be assembled by solvent welding or glueing, personally i trust solvent welding ABS better than glueing PETG.
- Included are two versions of the cover, one with my logo and one without
- Lastly, the basket model is super heavy due to its stupid amount of holes, depending on your pc/laptop your slicer work overtime for a few minutes.
Preparation (post printing):
- Turn on the printer and drive the Z-platform all the way to the top. In the photos mine is on the bottom for lighting reasons, i had to drive it up and down a bit during drilling.
- Turn off and UNPLUG the printer.
Parts needed:
Acetone and quetips for solvent welding.
3x M4 nylock nuts
3x M4x55 countersunk machine screws
2x M4x30 countersunk machine screws
1x Auxilliary fan off the Qidi Q1 Pro (details below)
The fan:
- First you need to unscrew and disassemble the auxilliary fan and funnel, the parts are solvent welded. What i did was pry them apart with a couple of screwdrivers, slowly breaking the bond by going around it a few times.
- The fan cable is long enough that unplugging it from the main board is not necessary. It is secured with tape along the bottom of the printer.

^This is the part needed, the rest can be discarded.
- The taps holding the fan housing parts together needs removing for a flush mount to the case.
- Alternatively, if you dont want to destroy the fan assembly or of you are building the filter for a different printer, the part can be sourched online or the whole fan assembly bought on the Qidi website.

^Part details.
Case assembly:

^Solvent weld/glue the backplates to the casing.

^Insert the fan as shown.
- It is a very tight fit to ensure it doesn't move or fall out during installation. So depending on warpage/shrinkage/print accuracy, you may need to file the square edges of the fan housing. - Mine fit just right.
- You need to decide if you want the fan cable going through the dividing wall or around it.
- So either you need to drill a hole through the wall while drilling the mounting holes.
- Or you need to make a small cutout in the case where you want the cable to exit.
- Important thing is the cable cannot be sandwiched between the wall and the case, that could cause clearance issues between the fan cover and Z platform.
Mounting the filter:
- Remove the enclosure back panel to reveal the main board and the backside of the dividing “wall”.
- The mounting hardware is mixed screws and machine screws all the same size, so take note of what goes where. Its easy enough to figure out during reassembly, but for convenience sake.

- Unscrew the 4 screws holding the mainboard in place, no further disassembly is required. This step is only precautionary, as the screwholes for the filter case clears the board with plenty of room to spare. Better safe than sorry tho, we dont want accidentally to kill an expensive part.
- On the inside, remove the poop bucket for better access.

- Here we see why the Z platform had to be moved out of the way, not too much room to work with.

- Now it gets a bit tricky as you need get the alignment right, and keep it right while drilling the first of the 3 mounting holes.
- Align the “cutout” with the cable hole top and sides, hold it in place and check that the case is sitting somewhat level in there.

- Using the “fifth hole” as a drill guide, drill through the dividing wall.
- Secure the case with a machine screw, just loose enough that you can rotate it with a bit of resistance.
- Re-check the alignment and drill through one of the two bottom holes.
- Secure it with another machine screw and drill the other bottom hole. Thats it for drilling, yay!
>Check routing of fan cable<
- Now tighten the first machine screw with a nylock nut.
- Remove the two bottom ones and fit the fan cover, reinsert the two screws through the cover and case, tighten/secure with nylock nuts.
- Re-mount the mainboard.

^Should look something like this, plenty of clearance.
- Now the enclosure back panel can be re-mounted, - reminder to re-plug all connections to the main board, that you may have unplugged.

^Secure the cover with the two top screws and thats it!
- Replace the poop bucket and we're done.
- For the first movements, drive the Z platform manually up and down all the way a couple of times. Check the clearance is good and even, and pay attention that no cables are pinching.
ENJOY!
Please provide feedback if you experience issues