BMG V6 Direct Drive mount for HeroMe Gen 5 (Stock Creality Gantry)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
The pre-existing Direct Drive solution for the HeroMe Gen 5 using a BMG extruder and V6 hot-end didn't take advantage…
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 11
- Wydruki
- 0
- Wyświetlenia
- 143
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial
The pre-existing Direct Drive solution for the HeroMe Gen 5 using a BMG extruder and V6 hot-end didn't take advantage of the built in V6 mount inside the BMG extruder. This meant the extruder was 40mm higher than required and used additional mounts, this added weight, extra Bowden tubes and moved the centre of gravity upwards. The solution also required you to use a new direct drive gantry.
This solution has the following improvements:
- Uses the built in V6 mount for the BMG meaning the highest quality direct drive possible.
- Lowers the extruder by 40mm making the centre of gravity improved.
- The 3D printed mount plate supports using thestock ordirect drive back plates. The Direct Drive backplate allows you to mount the extruder through the backplate as well for added stiffness. (optional)
- Hot-end cooling duct also diverts some flow upward to cool the pancake stepper. They usually run a little hot with this small amount of extra airflow they remain only slightly warm even when using high speed printing with linear advance enabled.
Retains stock mounting position for a BL Touch and fan mounts. I recommend the light weight 5015 fans but you can pick your own they all should work. Print Settings
Printer Brand:
Creality
Printer:
Ender 5
Rafts:
No
Supports:
Yes
Resolution:
0.2 <-> 0.32
Infill:
60%+
Filament: Any PLA works fine Any Notes:
I usually print at 200c PLA with 60c bed temp. I have done many long prints testing this hot-end and I haven't had any issues so printing this in PETG is purely for your own piece of mind as it's not needed if you have a correctly setup system.
I have designed the parts to havesome leeway if you don't have a perfectly calibrated printer but having a few drill bits and a sharp knife on hand could be useful if your print isn't perfect when it comes to mounting holes.
Hot-end
I use tree supports for the hot-end cooling duct. You should print the duct flat and upside-down. You can also print it standing up but you can sometimes have issues with the slicer not printing the duck fully in this orientation.
As this isn't holding any major weight you can dial back the infill and keep the weight down. I went as low as 20% without issues but for long life you could bump this up but anything over 50% is definitely overkill.
Back-plate
This thing should be printed flat with the part that mounts to the gantry on the plate. You might want to have supports on for the screw holes but you can have it disabled and just clean up with some tools before assembling.
For this I would go for 60% to 80% infill. Anything over 80% doesn't seem to add any strength and can sometimes cause printing quality issues if your extrusion isn't perfect.
Post-Printing
Required Hardware
- 1x 40mm Cooling Fan (you can use your existing one if you want)
- 6x M3 8mm Bolts a. 4x M3 8mm - Mount the backplate to the hot-end part b. 2x M3 8mm - Mount backplate to the gantry
- 2x M3 25mm Bolts a. 2x M3 25mm Bolts mount the fan to the hot-end duct
- 3x M3 45mm Bolts a. 3x 45mm bolts to mount the extruder and stepper to backplate. 5.Optional 1x M3 50mm a. Use instead of one of the 45mm bolts if you are attaching the backplate to the Direct Drive gantry.
- 8x M3 Nuts (used with the bolts above)
- 6x Small Zip-ties for cable management.
- 40x40mm Stepper heatsink
- Pancake stepper
- V6 Hotend (or suitable clone)
- Bondtech BMG Extruder (or suitable clone)
You will also need whatever nuts and bolts are needed to attach the fan ducts and BL Touch. You can get these from the HeroMe Gen 5 page.
Pre-assemble and check all holes etc
You'll be taking your printer apart so make sure you have all the bolts and the printed parts you've prepared are all ready. You can test assemble a lot of this beforehand adding the actual hot-end and extruder.
I HIGHLY recommend you check you have all the parts (including fan ducts, fans etc) and that they all attach together before you start final assembly.
Connect Hot-end Duct to Backplate
Attach the hot-end duct to the back plate using the M3 nuts and 8mm bolts listed above.
Attach fan to the fan duct
It's easier to get the fan attached now, you only will attaching it with the bottom two bolts. Pay attention to the cables, having the fan cable in the top left will make cable routing easier later on.
Install 6 zip-ties
This is fiddly work so best get it done now before the heavier parts get added.
Optional: If you have already dismantled your hot-end
You can check the back plate will mount to the gantry before you get too far into the process.
Install the Extruder and hot-end
The hot end can be fully assembled just make sure you alight the cable to exit on the right side when looking at it head on (see images). You'll need to wiggle the hot end so you can slide the rear portion of the extruder into place but as long as you're patient it should all come together easily enough.
I suggest you practise assembling the two parts without the hot-end duct in the way so you know what you're doing before you do it with the duct. This will also allow you to correctly setup the cog location on the stepper (IMPORTANT).
WARNING: You need to put a tiny bit of Bowden tube inside the extruder and it joins the top of the V6 and the actual extruder feed. It's tiny but easy to forget :)
Install pancake stepper and heatsink
Install the pancake stepper, make sure you previously tested you have installed the cog in the correct location. Stick on the heatsink.
Install your cooling fans of choice
Install the cooling fans you want from the HeroMe Gen 5 list I recommend the lightweight ones as shown in the picture but others should also work.
Optional: Install your BL Touch
Install your BL touch if you have one. You will need to have pre-printed the mounts.
Mount the entire thing onto the gantry
Just like the stock Hero Me Gen 5 mount the back plate onto the gantry using the two mounting points. This can be tricky but is possible with the fan ducts attached (tricky but possible) but it is NOT possible if you also install the fans so be careful.
Install the fans and use the zip-ties to cable tidy
Install the fans then use the zip-ties to cable tidy everything.
Get your firmware/software setup to use your new hotend
I won't include instructions on what to do here but you'll need to recalibrate the e-steps, retraction, z-offset etc.
You also will likely have to update a few other items like your terminator if this is a new hotend but you should be able to find tutorials on these parts if you get stuck.
How I Designed This
This was designed using Fusion 360 using the HeroMe Gen 5 mounts as an initial design then iterated on with multiple versions until I got to this version that was good enough to share.
I have attached an image below of the iterations and a mockup of the original HeroMe Gen 5 setup to show how high it is in comparison.
Category: 3D Printer Parts