LayersFactory
Zgłoś model
1 / 5
Qidi X-Max 3 Filament Cutter — zdjęcie 1
1 / 5

Qidi X-Max 3 Filament Cutter

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

3icad

3icad

@3icad_2273628

Auto filament cutter for Qidi X-Max 3. Useful for multi-colour printing using 3D Chameleon

Ocena
5 / 5
Polubienia
52
Pobrania
192
Wydruki
1
Wyświetlenia
1510
Oceny
1

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Other Printer Parts & Upgrades
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike
SzczegółyPliki (7)Wydruki i komentarze (Wydruki: 1) (Komentarze: 4)Remiksy (1)Kolekcje (84)Powiązane
Additional parts needed:
  • One spring. Ballpen spring works fine for me
  • Three screws. I used three 3x5 mm screws from my junk
  • One hobby knife blade #11. (https://a.co/d/eyljeUE)
  • A short (~17-18mm) Bowden tube. 
Printing:
  • I printed as oriented in the STL files. I tried different orientations for the blade holder, and this is the best for strength.
  • PETG preferred
  • DO NOT add support to the blade slot of the blade holder. Otherwise, you will not be able to insert the blade. X Max 3 can do a good job printing the overhangs for the blade slot.
  • Use tree support for the Bowden tube collet.
  • Print the included clamping clip or use any of your existing ones.

Assembling:
  1. Carefully insert the #11 hobby knife blade into the blade holder. Don't cut yourself. Note the orientation. I used another hobby knife to push the blade into the slot.
  2. Put the blade holder on one of the sides of the casing. Note the joint and orientation.
  3. Insert the spring. There is a knob on the blade holder and a groove on the casing.
  4. Close the case carefully without the spring popping out. Yes, it is a bit tricky.
  5. Secure the case with the screws.
  6. Try the cutter. It should be able to move and rebound smoothly.
  7. Insert the Bowden tube collet on the top. Fix the collet position with the clamping clip.
  8. Insert a short Bowden tube at the bottom.
Installation:
  1. Carefully remove the cable chain and Bowden tube.
  2. Align and insert the short Bowden tube into the extruder and mount the cutter to the cable chain hole platform.
  3. Make sure the cutter is level.
  4. Replace the cable chain.
  5. Insert the Bowden tube into the cutter. Make sure it is fully inserted.
  6. Place the trigger to the far left of the printer frame. Make sure it touches the end.
Video:
Gcode macro:
[gcode_macro CUT_FILAMENT]
gcode:
    SAVE_GCODE_STATE NAME=cut_filament
    G90 ; Absolute positioning
    M83 ; Relative position for extruder
    ; Go to the ready position
    G0 X10 Y290 F2000
    G0 X-5 Y305 F2000
    ; Cut!!
    G0 X-5 Y324 F2000
    ; Back to the ready position
    G0 X-5 Y305 F2000
    G0 X10 Y290 F2000
    M400 ; Finish the move
    RESTORE_GCODE_STATE NAME=cut_filament

 

Tagi

filamentcutterfilamentcutterqidi3dchameleonxmax3qidixmax3