1 / 6
Shower Head Holder (19mm and 23mm) - REMIX to add refinements — zdjęcie 1
1 / 6

Shower Head Holder (19mm and 23mm) - REMIX to add refinements

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Refined all parts with some chamfers and a toothed interlock system and a TPU rod gripper

Ocena
0 / 5
Polubienia
6
Pobrania
24
Wydruki
0
Wyświetlenia
162
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Bathroom
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

This is a really great original design, replacing commercial shower head holders for a fraction of the cost.

However I ran into a few difficulties with our heavy showerhead tipping down and a low grip on the vertical riser. 

The vertical riser TPU insert works superbly but is tricky to print, the bobble that fits into the end of the knob needs to be pointing upwards, which means the hollow bit that fits the rod needs to be facing the printbed, which means it needs support. That works absolutely fine, you'll get some scruffiness of the finish when removing the support but that just improves the grip on the rod even more and it's out of sight so no problem! If you don't have TPU, I suggest adding a self-adhesive cork or rubber “foot” to the end of the Right Knob to increase friction against the riser so you don't have to do the knob up so tightly. If you're using the TPU insert, you'll need to poke the bobble into the hole with a small screwdriver or similar implement to get it started through the hole in the end of the knob. It's designed to be a bit loose when in place, it has to spin in the hole so the TPU curve stays in contact with the rod while you tighten up the knob. 

The two original main bodies ended up with very smooth interface between them, and the Left Knob needed to be done up very tightly to hold the showerhead up. My first attempt at a mod involved printing a TPU friction washer which did help, but the knob still needed to be done up very tightly and after a month the joint between the threaded shaft and the knob failed. So I added a toothed interface between the two main bodies, and this works really well :o)

PRINTING -

I've orientated the STLs so they're the right way up for printing. But check they end up as follows-

Left/Right Knob, threaded end upwards, knob on the printbed. No supports. I added a block for the Left Knob in Cura when I printed mine so I could specify a small area of 100% infill just where the knob meets the shank for maximum strength, but the toothed interface probably means this bolt requires a lot less strength now.

ShowerRod body, print with the toothed interface at the top.

ShowerHeadHolder body, print as in the Fusion CAD image. If using support for the bolt hole, I suggest using block support suppression so the slicer doesn't try to support the tooth interface section and potentially spoil the neat teeth - that's how I did it. It needs support mostly for the shallow curve at the bottom of the round section. Ideally print with the holster hole taper narrow at the bottom and wide at the top, so the most visible top of the unit has the cleanest print if you have a textured bed. I recommend a brim for this part as it's inclined to lift at the corners for some reason. 

I'm finally happy with my holder now, and I'm hoping it will last ages :o)

Note that my photographed Right Knob is before I added the chamfer which I haven't printed yet, but I included the finalised chamfered STLs here.

UPDATED FEB 2026 - Ok well my "stronger" left knob lasted a year in constant use which isn't bad, but it failed at the junction between the threaded section and the plain shaft, so I'd recommend another block tool on the threaded section and some of the shaft, and I used 7 walls and 75% infill for that section and we'll see how long THAT lasts :o)