1 / 5
Flat Mesh Skirt with Wide Legs for Ender 3 NG — zdjęcie 1
1 / 5

Flat Mesh Skirt with Wide Legs for Ender 3 NG

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Allows for more space in the "basement" for electronics. Also looks cool.

Ocena
4,5 / 5
Polubienia
168
Pobrania
601
Wydruki
7
Wyświetlenia
2520
Oceny
6

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Share Alike

Mod designed for Ender 3 NG 

You can see the build process in Armor3d Printing's livestream. Check out his other videos too for more info about the E3NG and more!

 

Printing

Parts are already oriented properly for printing. No need for supports (they are built in where necessary).
CablesPassCover_x1.stl has 20mm bridging on the inside (not-visible), prints fine without supports.

Use any filament you want, parts aren't exposed to heat. I used PETG to avoid warping. Infill around 30%. 4 walls, 5 top/bottom layers.

Legs

Made to fit the stock rubber feet or any feet up to 28mm in diameter. Built in support (red in CAD pics) is meant to be removed, but can be left in place for additional clearance.

Accent color (orange) parts are optional. They are separate models. No need for filament changes or MMU.

For front legs use 2x M5x12 and 1x M5x45 SHCS and t-nuts to mount them. Black M5x45 bolts from the Ender3 can be reused here. If installed, you'll have to remove one M5 heat set insert from each front corner of the NG (frame_bottom_front_(left/right)_body.stl). Capture the bolt with an M5 nut or t-nut from above. (shown in pics)

Rear legs use 3x M5x12, the center one screws into the vertical extrusion.

Bottom accents are held with M3x8 screws and heat inserts.

Top accents are simply pushed into the holes.

 

Skirt

Each piece will fit each side of the printer, it's up to you. Normally the pieces with the ENG logo are meant to be on the sides. On the rear you have a choice of just clean mesh, mesh with an opening for cables and a version for D-Type modules (USB, RJ45, HDMI etc.) On the front you can use split meshes and a universal mounting bracket for displays (BTT HDMI5 1.2 frame is available separately).

Install mesh pieces using M3x8 and t-nuts. 2 screws are enough. If you want to use the long bottom accents, install them first with 2x M3x6, screw in from the top. They go directly into the plastic so be gentle. Then you can mount the skirt to the frame.

 

Front skirt

If you happen to have an inverted front already then this is plug and play.

However, most likely you have a stock skirt as the bottom piece on the front. You will have to replace it with the modified one - StockSkirtReplacement_x1.stl
It allows for M3x30 bolts to pass through and mount to the 2020 extrusion above using t-nuts.
It is partly compatible with the bottom “enclosure v2” panel - unfortunately the panel will have to be trimmed by 6-7mm (front) and secured with smaller mounts (EnclosureBottomPanel-SmallerMount.stl) if you insist on keeping it. A better idea would be to install a panel one level higher, on top of the 4040 extrusions. 

 

Side Skirt

Mesh with a logo can be used with a logo printed in accent color or in clear. You can use provided mount/cover for a Neopixel Button LED to light up the clear logo. Secure with M3x6 and heat inserts.

 

Rear skirt

The hole in the skirt is made for cables connecting the basement with the backpack. After installation cover the cables with CablesPassCover.stl

Example D-Type modules: https://aliexpress.com/item/1005008176772218.html

 

 

Updates

  2025.02.26

    Front meshes have been adjusted - gaps on the sides are 2.8mm smaller. Also mounting holes are now oval for better adjustement. STEP is updated as well.

  • FrontSkirtClean_x1.stl
  • FrontSkirtLogo_x1.stl
  • FrontSkirtL_x1.stl
  • FrontSkirtR_x1.stl

 

 

Tagi