Extruder Body for printing Flex Filament (fits CM3D Extrusor MINI)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Extruder bodies for PRUSA MINI with the ability to disable the IFS without disassembly (for printing flexible filament)
- Ocena
- 0 / 5
- Polubienia
- 5
- Pobrania
- 14
- Wydruki
- 0
- Wyświetlenia
- 237
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Prusa Parts & Upgrades
- Licencja
- GNU General Public License v3.0
The Extrusor with integrated filament sensor by Comunidad Maker 3D (or any filament sensor that drags on the filament) has a problem with flexible filament. The extruder will pull the filament through the sensor just fine, but retraction can result in the filament kinking and jamming in the gears. The original Extrusor must be removed from the Z-carriage to take out the steel ball from the sensor so flexible filaments can be printed, and I did not like that.
The FLEX version of the body allows you to disable the filament sensor by tightening an M3x12 screw (reused from the original Prusa MINI extruder), which lifts the stainless-steel ball out of the filament path.
Making some shims to align the gears with the filament path, such as the CM3D and Vertex Extruder Spacers and CM3D and Vertex Extruder Lever Remix by William should also improve TPU printing. Shims for the primary drive gear bearings and the lever are included.
All other components and instructions can be found at original CM3D Extrusor MINI + FS page.
There are three build paths depending on what hardware you have available.
- If you have an Extrusor on your MINI already:
- Print the FLEX version of the body, reusing all the gears, screws, filament sensor components, carriage, and tension lever from the original Extrusor.
- One M3x12 needed for “DISABLE SENSOR” screw hole.
- If building from a Triangle Labs MINI extruder:
- Print the cover and body labeled TL. Reuse the gears, screws, and tension lever from the Triangle Labs extruder.
- The filament sensor components from the CM3D Extrusor (extrusor_mini_FSLever_v7.4 and extrusor_mini_fsmodule_v7.4) will need to be printed and assembled using the IR sensor, magnets, and stainless-steel ball from the Prusa filament sensor.
- The CM3D Z-carriage to replace the Prusa rear Z-carriage is recommended as well (it adds a third screw to mount the extruder assembly).
- Note: The outlet is also deeper to accept the longer threads on the Triangle Labs fitting. This is the only variant with the tubing collet for the inlet since I do not have other brands of collets to ensure fit.
- If replacing the Prusa extruder:
- Print the cover and body labeled R. The only screws needed are the M3x25 and M3x12 from the Prusa extruder and filament sensor.
- You will need the same filament sensor components and Z-carriage as the Triangle Labs build, but you also need the tension lever from the CM3D Extrusor (extrusor_mini_lever_v7.4) and a gear kit (gears, bearings, shaft, and thumbscrew). Make sure the drive gear on the stepper motor is mounted with the end with a set screw facing away from the motor.
Important notes on adjusting hardware settigns! Read verification test section even if you have already adjusted E-steps and motor direction with previous installation.
In the experimental settings menu on the latest MINI firmware, you will need to change the extruder steps to 415 and extruder direction to “wrong” for the extruder to initially work.
Verification Test: The e-steps can be precisely set by marking the filament in two places 100mm apart, manually adjusting the E-axis until the first mark is at a good reference point (I have a clear bowden and used the end of the fitting as my reference, see picture). Scroll the E-axis until it says “100” and wait until it stops feeding, then make slight adjustments until the second mark is lined up with the reference point. Note the number and go back to the experimental menu. The formula for adjusting is E-steps is: number from test ÷ 100 x current setting = correct number for your gearset, e.g. my test result was 102 (indicating it had been underextruding by 2%), current setting was 415, so 1.02 x 415 = 423 extruder steps. Rerun the test to verify manually advancing the extruder to 100 actually moves 100mm of filament.
Additional Notes:
- I recommend tramming your printer and calibrating the extrusion multiplier before you start to make sure the parts will not have any misalignment of the shafts and gears.
- If modifying an existing CM3D Extrusor, it's a good idea to print the CM3D and Vertex Extruder Cover Remix (ziptie reuse) since you will probably be taking the cover off a few times to shim the gears and arm. The TL and R cover variants I have are already set up for ziptie reuse.
- When shimming the gears and tension lever, the lever shims are also used on the secondary drive gear.
- The gears should turn freely with at least 0.2mm of axial play on the shaft (a scrap PLA skirt from a print works well as a feeler gauge.
- The primary drive gear play should be checked with the motor screws torqued, or you will have binding when the Extrusor is assembled.
- The primary drive gear can be easily shimmed to the center visually, but the secondary drive gear must have the lever shimmed first and be checked by looking down the filament path.
- The filament sensor connector clip may get in the way and can either be cut off or the 5v and ground wires swapped in the connector so it can be flipped. Make sure the red wire is connected to the pin labeled 5v.
- The spacer fits over an M3x40 screw so it can be used to disable the sensor instead of an M3x12. The longer screw is easier to see if the printer is in an enclosure that blocks access from the side.
- Last picture is of the first TPU retraction test print (TPU on PLA raft).
