1 / 7
MK4S/MK3.9S Fan Shroud Light Filament holder — zdjęcie 1
1 / 7

MK4S/MK3.9S Fan Shroud Light Filament holder

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Mod that adds lights to your MK4S/MK3.9S hotend.

Ocena
0 / 5
Polubienia
13
Pobrania
14
Wydruki
0
Wyświetlenia
391
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution

This is a mod that adds an LED filament around your hot end. To go with it, I’ve included steps to hook it up to your GPIO board and trigger it with GCode. 

 

Printing

Printed with PCCF (Amazon) to match the shroud. You might get away with a lower temp material, I don’t know. It's possible I could print this for you in PCCF… We can discuss. Drop me a line.

Print with the led filament channel face down. I've been using a brim, but the PCCF seems to stick really well, so it might be optional. 

I had difficulty "Thermal Run Away" printing this part. The part fan would turn on and that dropped the bed temperature significantly, enough to cause a failed print. I fixed this by modifying the filament settings to only use 10% fan, and to only turn it on at the 10th layer and above. However, the cooling of the final tippy-tops of the part was inadequate, causing some overheated tops, but the rest of the print looks good.

I am using this textured sheet which is quite thin. It might be that if you used a thicker textured sheet the over-cooling effect would be reduced. Or an enclosure might help. 

Your mileage may vary.

 

Assembly

  1. Electronics assembly
    1. (TODO: Upload Schematic)
    2. Run wires from GPIO to circuit to LED.
    3. Run wires along / within the wires leading to the hotend
    4. You can, with some effort, get the LED wires to follow the wire path that the rest of the wires take. I used a combination of fishing with a small zip tie and a thin band of electrical tape to accomplish this. Be patient, you wouldn't want to damage any other wires at this time.
    5. Insert the LED filament into the filament channel.
    6. At this point, the printed part and LED should adhere together by friction, and it should be dangling from your hotend.
  2. Unscrew the m3 torx screw holding the shroud to the fan case.
  3. Replace the screw with a 12mm m3 screw (I used a socket head)
  4. Screw the LED holder and fan shroud together, sandwiching the fan casing between the two.
  5. The LED holder should be mostly in place now, the LED channel should be parallel with the fan shroud's "blow hole".
  6. On the opposite side of the hot end part fan casing, 2 holes should be aligned with 2 screws, holding the fan to the fan casing.
  7. Remove these screws, and attach the LED holder to the fan casing with 12mm m3 screws (again, I used a socket head).

Hardware

The m3 torx screws that came with the original parts were replaced with 12mm m3 socket heads (x3) to allow for the extra material.

 

Electronics

For the light source, I'm using Cool White 3v 30ma 1.8 OD 130mm led ‘noodles’ (aka Edison LED filaments) that I sourced from AliExpress. AdaFruit has some similar options.

I'm using the GPIO board with a separate USB power supply (could likely be sourced from within the powerpower box) (USB Breakout Board or modified USB cable)  and a 100-150 ohm resistor (I don't remember which I settled on, but both should be fine). I'll have a schematic here sooner than later.

The circuit is basically 

  1. USB + to LED +
  2. LED - to GPIO 1
  3. GPIO GND to Resistor
  4. Resistor to USB -

You an probably accomplish this without a board at all, or maybe use a Perma-Proto board.

Consult the PCB image (I'm still finalizing the PCB, but if you want to order one, drop me a line, it'll motivate me). You only need 1 resistor. There are two on the PCB prototype to make it more accessible.

GCode

I added the following GCode to the Printer Profile under Start G-code:

; Lights on!
M262 P0 B0
M264 P0 B1

And this to the End G-code

M264 P0 B0; Lights off!

I have another machine that has LEDs tied to a Duet Smart Effector Platform, that turn on automatically when the hotend is heating, so I tried to achieve something similar by placing these codes just before the hotend starts heating, and just after it turns off.

 

TODO: 

  1. Clean up model
  2. Add parametric variables to the model

On Onshape.

Tagi