Sword of Seven Truths (Hardcore Leveling Warrior Earth Game Version)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
The Sword of Seven Truths from the Hardcore Leveling Warrior: Earth Game webtoon
- Ocena
- 0 / 5
- Polubienia
- 5
- Pobrania
- 20
- Wydruki
- 0
- Wyświetlenia
- 137
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Props
- Licencja
- Creative Commons — Attribution
Printer: Bambulab X1C
Filament: Overture Pla
- General settings
- Wall loops: 3
- Since the infill needs to be low to reduce weight
- Layer Height: 0.2mm
- Infill: 1%
- Sparse infill pattern: Grid
- Support: Normal
- Brim Type: Outer brim only
- To help combat lifting corners since there are some pretty large piece
- Wall loops: 3
- Connector
- Infill: 5%
- No reason, you can leave it the same as the general settings if you want. It's mostly to help with aligning the jewels.
- Infill: 5%
- Jewels (End Jewel and Cross guard jewel)
- Infill: 5%
- Wall loops: 3
- Layer Height: 0.1 mm
- Guard
- Infill: 8%
- No particular reason. You can increase or decrease this as much as you want. Just remember the overall weight of the sword.
- Sparse infill pattern: Gyroid
- No particular reason
- Infill: 8%
- Cross Guard
- Infill: 8%
- Handle
- Infill: 2%
- The walls of the handle are thin enough that most of the structure should be taken up by the walls. The pipe will be responsible for supporting the weight, so the handle is basically just a cover for it.
Printing & Assembly
- 1 Guard
- 2 Guard jewels
- 2 Cross guards
- 4 connectors for the cross guards
- 3 End jewels
- 2 for the cross guard
- 1 for the handle
- 1 Handle
- 1 connector
- All 10 blade parts
- 1 1-inch copper pipe cut down to 43 inches
Tried my best to size everything accordingly based on the webtoon. The sword isn't always a consistent size or shape a lot of the times though. I estimated Hardcore Leveling Warrior to be about 5'8 and sized it based on that. So the length comes out to ~4 ft (48 inches).
Parts can be further split up in your slicer of choice if the pre-sliced files don't fit on your bed. I'm also providing all of the parts without any of the connection points or clearances to allow for easier remixing if needed.
I left the handle and cross guards plain. In the webtoon they have a leather wrap and I wanted to make it easier to do that. You can wrap it any way, but I believe that either a gaucho knot or bight turk's head knot are pretty close.
This build uses a copper rod to support the weight of prop. Due to the design, all of the weight ends up out on the end of the blade, rather than being more balance or towards the guard like most swords. Personally I'm using JB Weld to fix the pipe. No matter what glue you use, I recommend taking a file to the pipe to scratch it up a bit. It'll give the adhesive something to bite into. I got mine from Home Depot and it was pretty long. I'd would pick up a pipe cutter as well, just to make chopping it up easier.
If you want to be able to disassemble this for traveling or storage. Then glue 2 or 3 of blade pieces together in batches, mostly to consolidate the pieces. Use a bit of painters tape to keep the blade and handle fixed in place. Once you're ready to break it down, it should be easy to pop the pieces off. Just make sure you don't use too much tape and be careful when breaking it back down, as some of the larger blade pieces will be a little weak on the top and bottom surfaces due to the low infill.