Neptune 4/4pro Y-Axis Double Shear 9mm Belt Upgrade
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
upgrades the Y Axis with 9mm Belt and beefier Motor
- Ocena
- 5 / 5
- Polubienia
- 49
- Pobrania
- 172
- Wydruki
- 2
- Wyświetlenia
- 1350
- Oceny
- 1
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
For whom is this for?
Its for Madmans thinking one day the N4 could be an LH-Stinger - it cant - but we try anyways! This Mod is for N4 or 4Pro owners that seek for more power overall on the Y Axis which means higher recommended accel, higher peak accel, higher belt tension, less vibrations and potentially less VFA.
What it does
This mod will relocate the motor lower to allow adding a longer motor then stock. Using the Moons Motor will allow the use of a bearing to make the motor shaft double shear. This in return allows to be much more aggressive on belttension which in return will improve Input shaping.
What to buy(BOM)
- 1x Biqu Moons MS17HD6P420I-04
- 1x 9mm x 1m Gates LL-2GT epdm belt
- 4x M3x40mm shcs or bhcs
- 3x M3x5mm shcs or bhcs
- 1x M3x25mm bhcs
- 2x M3x6mm fhcs
- 4x M3x3(L)x4.2mm(OD) Heat Insert
- 3x M5x22mm Cylindrical Locating Dowel Pin 304 Stainless Steel
- 2x 9mm GT2 Idler Pulley 20T Runice/Mellow 15mm OD (not 16mm)
- 1x 9mm GT2 Idler Pulley toothless Runice/Mellow 15mm OD (not 16mm)
- 1x 9mm GT Timing Pulley 20T Runice/Mellow/Gates 15mm OD(not 16 or 18mm)
- 1x F625 Bearing with flange ABEC7 or ABEC9
- 2x 1.8 or 2.5mm wide Cable Tie
- 1x M4x6x10mm Heat Insert for Small LS Bed Leveling Knobs (otherwise rear left bed knob will hit motor)
note: instead of 2x 9mm gt2 toothed pulley + 1x 9mm gt2 toothless you can also order 3x 9mm gt2 toothless instead. Performance is identical.
Print recommendation
- ASA/ABS-cf/gf good, PETg-cf/gf OK
- Layerheight/width: 0.2/0.4
- Walls: 6
- Toplayer: 6
- Bottom Layer: 4
- Infill: 10%
- no supports, PartA recommended support from buildplate
- no brim required
Version Log
v79 - optimised screw in plastic thread design, minor optimisations
v78 - widened Beltclamp rim
v76 - updated PartA to solve motor shaft getting out of alignment of the bearing
v71 - updated PartA resolves clearance issue and added strength
v70 - updated Part A & B, added alignementtab, strengthened upper Screw holes
v68 - updated PartA, PartB resolves clearance issue, updated Documentation
v64c - updated Documentation
v64b - updated Documentation, added Bed Knob as required item
v64 - release Version