The Juicer - An extruder mod for the Lemontron
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Extruder mod for the Lemontron that improves on torque and thermal issues.
- Ocena
- 0 / 5
- Polubienia
- 8
- Pobrania
- 40
- Wydruki
- 0
- Wyświetlenia
- 321
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
If you aren't already using the new lemonstruder, you should try using that instead of this!
This is a modded extruder for the Lemontron that adds torque and helps keep the filament pushing gear from overheating and softening the filament, which is an issue I had with my motors.
All parts are printed in the given orientation. A 0.4mm nozzle with 0.2mm layer heights, existing completed Lemontron and another well tuned printer is assumed.
No non-printed parts that aren't part of the original Lemontron BOM are mandatory.
Printing:
- Big gear: Thermally resistant, tough and rigid filament needed (glass/carbon filled nylon, ASA, ABS). 100% infill with supports under the center. Minimum 4 permimeter lines.
- Small gear: Thermally resistant, tough and rigid filament needed (glass/carbon filled nylon, ASA, ABS). 100% infill, no supports needed. Minimum 4 permimeter lines.
- Left midplate: Thermally resistant filament needed, as the original build guide mentions.
- Left top plate: PLA is fine for this and it is unchanged from the original by Blenden and simply included in this for ease of downloading.
Assembly:
- Remove your current left top and mid plate
- Lubricate contact surfaces with a plastic safe lubricant like silicone grease
- Remove BMG extruder gear from motor shaft
- Place small gear over motor shaft. Tolerances are tight so you may have to gently file down the inside a little.
- Press fit BMG extruder gear (the one you cut when originally assembling the Lemontron) into the big gear. It's a tight fit and you may find it easiest to push an M5 screw through and use an M5 nut to tighten it down to be the easiest way of doing this. Make sure that they sit together as flat and tight as possible!!
- Push 2 needle bearings (You know, the ones that came with the BMG gears you ordered? You didn't throw those away did you :P) over a 16mm button/flat head screw and then push the big gear assembly over that.
- Screw big gear assembly into the screw hole extruder motor (the one closest to the main board)
- Install the new mid plate as per original Lemontron instructions, making sure no wires are tangled or touch the gears. Using some tape to form a barrier between gears and wires may be useful.
- Put the original filament spring-bearing pusher thingy from your old top plate into the new top plate
- Install new top plate
- Boot your Lemontron and edit Klipper's printer.cfg to account for the new extruder. You'll need to recalibrate it. My rotation_distance is 15.66, which you can use as a starting point but you should really try calibrating it yourself too for best results.
- When calibrating, you NEED to watch the filament get extruded the whole time. If at any point it briefly stops extruding, it means something has gone wrong. Either the filament pushing gear isn't flat or the small gear on the motor shaft is too lose.
This is a remix of the belt drive mod and the mid and top plates are edits of the ones found there. The top plate is unchanged, I've only included it for ease of use.