1 / 5
Fisher Price Garage (#930, 1970) repair parts: human elevator car and belt — zdjęcie 1
1 / 5

Fisher Price Garage (#930, 1970) repair parts: human elevator car and belt

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Our old Fisher-Price garage toy (#930, 1970's version) was broken in two significant ways: (1) the belt was broken and…

Ocena
0 / 5
Polubienia
3
Pobrania
35
Wydruki
0
Wyświetlenia
168
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Our old Fisher-Price garage toy (#930, 1970's version) was broken in two significant ways: (1) the belt was broken and therefore the elevator did not work. (2) The people elevator, outside the elevator tower, was broken in pieces and broken off of the car elevator.

I made a new belt which seems to work nicely when printed out of TPU, and a new bottom piece for the human elevator car. The new human elevator car is made to securely attach to the car-elevator-car with three attachment points to the stub which remained on the car elevator.

I also made 4 clamps which were necessary to hold the two halves of the elevator together during re-asassembly.

Please note that the external elevator car bottom included here is designed for the particular way that ours broke off of the internal elevator car. A re-design may be necessary for some other case.

The clamps were only needed because the relevant screws had no way of backing them out. I've seen pictures of other versions of the garage toy where the screws did have slots, just like those on the bottom of the base-plate. In that case, you might not need the clamps.

The elevator seems to work very well.

xakerofxanthi has designed many other parts for this toy. He also, based on a query of mine, designed a belt, but I designed and made this one before seeing his.

Print Settings

Printer Brand:

Creality

Printer:

K1

Supports:

Yes

Infill:

Varies

Filament: Creality and Matter Hackers ABS and TPU Notes:

I used ABS for the elevator car and clamps, but PLA or others should work. Flexible TPU worked nicely for the belt and made installation of it easy.

I used brims to help hold the ABS pieces to the build plate. I placed the human, external, elevator car on its edge (front or back as it sits attached to the garage) to minimize any support (tree) debris where it would hamper the fit of the tabs.

Post-Printing

The elevator was separated from the rest of the toy by removing the 4 screws from the bottom of the base-plate and gently prying the 3 clips that hold it to the garage/ramps. The two halves of the elevator tower were separated from one another by cutting through the screws/pins that hold them together with a cut-off wheel on a dremel-like tool, taking care to cut the minimum amount of plastic. The screws had to be cut since they have rounded heads with no slot or other feature for a screw-driver or other driver of any kind. I could drive out the half of the screw that contains the head, but couldn't drive out the other part of the screw; the tip with more threads/flutes on it. This is why the clamps were needed: part of the screw was still in there and needed to be worked around.

With the screws removed from the tower, the two parts were separated and the elevator car removed from the rod that holds it in position and then from the belt. The TPU belt was fitted around the drive pulleys. [Note that any time I touch TPU, I end up with stringing and had to clip away tons of extra material on this belt...] With the elevator car out of the tower, the screw that used to hold the external and internal elevator cars together was removed with a pair of pliers. The hole was drilled out to 1/8 inches all the way through the stub. The new external car was fitted to the stub with the top two tabs above and below the tab on the internal car and the third, thinner, tab below the stub. All of the tabs and the stub were held tightly together while using an M4 x 0.7 tap to create threads in the hole all the way through the pieces.

1/8 inch holes were also drilled through the bosses, or whatever they are, which hold the two halves of the elevator tower together with screws. Holes were only needed for the 'back' piece that sits against the garage and those holes were only drilled until the bit contacted the half of the original screw that remained. These holes were also tapped to M4 x 0.7. The bosses on the 'front' half of the elevator tower, which sits away from the garage, were not drilled as they are a good size, but they were tapped to M4 x 0.7.

With the two elevator cars fastened to one another, the rod was re-inserted and the internal car attached to the belt. The stop signs/gates were re-attached to the tower and the tower halves pushed together. The clamps were fitted and 8 M4 x 8mm screws used to attach them to the tower. The tower now will not separate. The tower was re-clipped onto the garage and the 4 original screws used, from the bottom, to fasten the tower to the base-plate. I recommend going slowly and carefully as you are working with old brittle plastic.

The top, clear, portion of the external car was clipped onto the new bottom piece and a little super glue used on the top piece's bottom edge to hold it securely to the bottom piece.

How I Designed This

I used this project to familiarize myself with solidpython so that I could use all the features of the python language instead of directly programming in openscad. The .py files are included, and not the scad files, since the latter are excessively ugly; especially when using loops.

Measurements were taken from the original pieces and a few adjustments were made for ease of design or for robustness. The corners and edges of the external car bottom were not rounded to save time and hassle.

Requirements: 8 x 8 mm M4 screws (only necessary if clamps are necessary) 1/8 inch drill or similar metric for starting M4 screws 1 x 25 mm M4 screw [optional] M4 tap a few drops of superglue

Category: Mechanical Toys

Tagi