1 / 5
Ubiquiti UNIFI G3 / G4 Pro Camera Cable Gland Mold — zdjęcie 1
1 / 5

Ubiquiti UNIFI G3 / G4 Pro Camera Cable Gland Mold

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Mold for creating Ubiquiti G3 and G4 Pro cable glands. UVC-G4-PRO / UVC-G3-PRO

Ocena
0 / 5
Polubienia
1
Pobrania
27
Wydruki
0
Wyświetlenia
161
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Photo & Video
Licencja
Creative Commons — Attribution — Noncommercial — NoDerivatives

I couldn't find Ubiquiti camera cable glands.

Necessity resulted in creation of molds to make replacements.

The G4 Pro and G3 Pro use same cable gland.

Also made a mold for the G4 / G3 Bullet, in another listing.

The approach in designing the G3/G4 Bullet and the Pro Molds is the same, but the design builds are NOT.

Recommended Print setting (from

https://forum.creality.com/t/step-by-step-guide-to-creating-3d-printed-molds/23431 )  4 top and bottom layers using a 0.1 mm layer height.

  • If you use PLA, you may find it works better painted.
  • ABS or PETG may be a better filament choice.
  • RTV Sealant (Permatex Gasket Maker) works well.

Ubiquiti G4 - Cable Gland Molds

By m2radar

Mold consists of two bottoms (one vented, one not), middle and top section (with vents). Choose vented, for RTV, or closed bottom, for liquid silicone.

  • For RTV
  • Humidity (moisture) and temperature are both essential, for RTV curing.
  1. Smooth the mold interior and apply a thin layer of (petroleum jelly) lubricant.
  2. Apply thin layer of RTV to mold inside bottom and middle surfaces (while apart)
  3. Let RTV begin to cure.
  4. Combine bottom and middle section.
  5. Fill to top of mid-section, and apply some RTV to top, ensuring sufficient RTV to compress into mold.
  6. Let RTV begin to cure a slightly.
  7. Secure the top by firmly pressing together.
  8. Verify silicone squishes out of openings, to indicate mold is full.
  9. For RTV, humidity (moisture) and temperature are both essential, for curing. Simply drop mold into a container of water and let it stand at room temp (70 degrees plus) at least a full 24 hours.

 

  • For Liquid Silicone
  1. Smooth the mold interior and apply a thin layer of (petroleum jelly) lubricant.
  2. Put together the bottom and middle section.
  3. Fill mold level to top of mid-section.
  4. Let the top of the mid-section begin to cure a little.
  5. Secure the top by firmly pressing together.
  6. Apply liquid silicon into top holes, tilting to ensure it goes into peak.

Store in a warm environment.

Have patience. Placing in hot car during summer time expedites the process.

  • After initial curing time, detach mold petals by pushing them in to delaminate.
  • Carefully open each end and work around main body of gland, to delaminate.
  • Remove new cable gland.
  • Use scissors to detach gland petals.

Let gland continue to dry and cure, for another day.

You can also print the included model using TPU Filament.

Be sure you research and setup your printer properly to achieve a good outcome.

 

 

Tagi