Red Sea Max Nano Peninsula G1 Nanomat Adapter
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
I bought a used Red Sea Max Nano Peninsula and was not sure whether I had a G1 or G2. When my Red Sea Nanomat arrived…
- Ocena
- 0 / 5
- Polubienia
- 4
- Pobrania
- 113
- Wydruki
- 0
- Wyświetlenia
- 637
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Ideas
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
I bought a used Red Sea Max Nano Peninsula and was not sure whether I had a G1 or G2. When my Red Sea Nanomat arrived it quickly became clear that I have the G1 and was going to need to find a way to make it work
2025-08-21 update: added overflow_cover.stl which is a replacement divider/weir with a cutout to help accommodate the odd shape of the nanomat without bowing
suggested materials and print settings
clear PETG
black ABS
layer height: 0.15
PETG note: 4+ perimeters
perimeters: 3+
support settings for overflow_cover.stl:
style: snug
pattern: rectilinear
pattern angle: 45°
support on build plate only: unchecked
optional: increase XY separation between an object and its supports to 1-2mm
notes:
this took me several attempts to find a combination of settings and integrated breakaway support structure to get to print without severe warping on the top side. The shape is not well lent to standard 3D printing, but it can work. The supports are annoying to remove; the suggested pattern angle setting is specifically to make it less frustrating to completely remove and clean up the part. I used Overture black ABS for my latest design and it doesn't look very out of place at all
installation instructions
okay so step one is a real pain in the butt but you need to first remove the built-in sock holder. Mine was attached solidly to the side and back with little foam adhesive circles. I was able to use a scraper to cut through the ones on the back and then used leverage and grit to "twist" it free of the other side. It was a real struggle but it is possible. The front side is not adhered, it just slots into the plastic divider below the removable divider/weir. This piece can and needs to be completely removed intact, because my adapter slots into the same space space that the sock holder is in. And that means if you ever decide to change it back, it remains possible. Anyway if you don't break the plastic you also don't have to worry about getting the shavings or shards out of the back lol
take about 20% of the water out of the tank so that the water level is below the bottom of the divider. Take the rear shade off temporarily (the hingey thing) and pull the removable divider/weir out. Also take the protein skimmer out temporarily as well. Then you should be able to finally remove the built-in sock holder. Keep at it, it was quite a struggle for me but it did eventually come loose

once that's removed you can snap the adapter into the same place. The fit should be a bit snug, Once the adapter is in place you can put the protein skimmer back inonce that's removed you can snap the adapter into the same place. The fit should be a bit snug, Once the adapter is in place you can put the protein skimmer back in
next you slide the nanomat housing into the adapter

then you can put in the divider and replace the shade. The nanomat was not designed with the dimensions of the G1 in mind so the final assembly of the nanomat itself is also slightly modified to make up for this. It does not impact performance of the device in terms of filtration, but is unfortunately slightly less convenient than the original design. This is unfortunately necessary in order to get the device to actually fit at the expected depth but it's a small compromise
The roll holder hangs on the side of the rear shade like a holster. Use the spindle that comes with the nanomat in this holder, as pictured

from here the filter floss should be routed the same way the instructions show, around the bottom, back up the far side, and onto the receiver spindle. The sensor can be installed in the normal spot, etc, no further modification is needed.
It works fine without my replacement divider but there's a round piece of plastic that serves as a channel for the sensor wire and that presses against the divider and bows it out ever so slightly. It also makes it difficult to fully put the nanomat back into the base after changing the roll because the back of the spillway gets in the way. My modified piece is a near-exact copy of the original but has a rounded space removed in the right spot to solve this issue


this picture shows the nanomat fully installed with the new divider. you can see part of the cable channel just above the cutout.
Finally though, it should all be working, and, it's all compatible with both the included skimmer and ATO
so far a roll of nanomat filter fleece lasts me 2.5-3 months. they come in 3 packs so the running cost is quite low so far