Prusa MK4/MK4S X-Axis Thumb Knob Belt Tension
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Prusa MK4/MK4S x-axis belt tensioning with thumb knob
- Ocena
- 0 / 5
- Polubienia
- 30
- Pobrania
- 76
- Wydruki
- 0
- Wyświetlenia
- 794
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Prusa Parts & Upgrades
- Licencja
- GNU General Public License v2.0
This allows for easy and quick adjustment of the X-axis belt tension using a knob.
The size of the parts in this mod is not the same as the original, so some other mod or accessory may not be compatible with this.
X-End-Idler dimension difference in XY plan

Z-Bottom-Right dimension difference in XY plan

Z-Top-Right dimension difference in XY plan

My Print Settings
- Nozzle 0.4mm
- Layer height: 0.2mm (0.15mm for x-end-idler-pulley-carriage)
- Perimeters: 4
- Infill: 15% Gyroid
Extra Parts Needed

For new X-End-Idler
- 1 x M3x18mm Socket Head Cap Screw
- 1 x M3 DIN562 Square Nut
- 1 x M3x35mm Socket Head Cap Screw
- 1 x M4x35mm Socket Head Cap Screw
- 1 x M4 Anti-Slip Hex Nut
For Self Printed Knob
- 1 x M4 L6D6 Heat Insert Nut
- If don't want to use self printed knob, can also use M4 Thumb Nut or M4 Clamping Knob for alternative
Prepare x-end-idler-pulley-carriage
- Use M4x35mm Socket Head Cap Screws and lock with Anti-Slip Hex Nut


Prepare x-end-idler-tension-knob
Insert the M4 L6D6 Heat Insert Nut into the x-end-idler-tension-knob


Check the back of the knob is not being blocked by the melted plastic

Disassemble The Printer
- Unlock the 3 screws behind the Nextruder to remove the x-cover

- Remove the x-axis belt from x-end-idler


- After remove the belt from x-end-idler. Put the belt back and cover the x-cover back to the Nextruder


- Remove z-top-right part

- Move x-carriage assembly to the top and the Nextruder all the way to the left

- Hold the x-carriage assembly with tape

- Unscrew the 4 motor screws in z-bottom-right

- Remove the smooth rods and lead screw

- Cut the zip tie under the right motor to access the three screws, then move the motor to unscrew the three screws holding the z-bottom-right.

- Remove z-bottom-right and x-end-idler

Build the New X-End-Idler
- Most of the parts can be transplant from the original x-end-idler
- Insert the bottom screw

- Insert the top screw and square nuts

- Put the lead screw nut back
- There's no need to tighten the two screws; they will need to be removed for centering the lead screw later. The screws are just for holding the square nuts in place to prevent them from falling out.

- Insert the bearing clip. Insert the square nuts and M3x18mm screws from the original x-end-idler

- Insert the prepared M3 DIN562 Square Nut and M3x18mm Socket Head Cap Screw to the top left of the bearing clip


- Insert the hex nut from the original x-end-idler

- Insert the prepared M3x35mm Socket Head Cap Screw to the bottom left of the bearing clip

Reassemble the Printer
- Install x-end-idler-for-belt-tensioner to the x-carriage assembly

- Install z-bottom-right-for-belt-tension

- Insert the smooth rod


- Centering the lead screw and Tightening the motor screws
- Remove the lead screw nuts temporarily from the x-end-idler
- Centering the lead screw
- Reinstall the lead screw nuts back to the x-end-idler
- Remove the lead screw nuts temporarily from the x-end-idler
- Install z-top-right-for-belt-tension and then remove the tape holding the x-carriage assembly


- Put the belt and pulley wheel into the x-end-idler-pulley-carriage and hold it with the pin


- Put the x-end-idler-pulley-carriage into x-end-idler-for-belt-tensioner


- Tight the belt with knob

- Note: Do not let the x-end-idler-pulley-carriage stick out from the x-end-idler-for-belt-tensioner. This may affect the calibration test.

Recalibrate the Printer
- Check the belt tension for x-axis

- Turn on the printer and run the calibrations
- [Control] > [Calibrations & Tests] > [2 XY Axis Test]

- [Settings] > [Input Shaper] > [Calibration]
(The value for your printer may be different)
- [Control] > [Calibrations & Tests] > [2 XY Axis Test]


