wastebagroll-holder / Mülltütenrollenhalter
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Orientacyjna cena wydruku pliku
0,48 € – 0,58 € netto (bez VAT)
Dla pliku: holder_0.2mm_PLA_MK3S_31m.gcode
To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.
Plik i założenia wyceny
Plik użyty do wyceny
Średnia wycena orientacyjna: 0,53 € netto (środek widełek).
- Masa podana przez autora
- 7 g
- Czas druku podany przez autora
- 30,6 min
- Materiał u źródła
- PLA
- Materiał wyceny
- PLA
- Drukarka wyceny
- Bambu Lab P1S - 0.4 nozzle
- Proces wyceny
- 0.20mm Standard
Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.
Zapisane na tym urządzeniu.
Simple holder for rubbish bag rolls to be plugged together. Einfacher Halter für Mülltütenrollen zum zusammenstecken.
- Ocena
- 5 / 5
- Polubienia
- 2
- Pobrania
- 16
- Wydruki
- 2
- Wyświetlenia
- 451
- Oceny
- 1
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Kitchen
- Licencja
- Creative Commons — Attribution — Noncommercial
English available below
Einfacher Halter für Mülltütenrollen zum zusammenstecken.
Zur Auswahl stehen zwei Seitenteile und zwei Halter. Der hohe Halter (holder high edge.stl) sollte verwendet werden, wenn man den Halter an einer Schranktür befestigt, damit die Rolle nicht herunterfällt.
Ihr benötigt einmal die Grundplatte (base), insgesamt zwei Stück von den Seitenteilen (solid und/oder open) und insgesamt acht Stück von den Haltern (holder und/oder holder high edge).
Zur Befestigung sind zwei Senklöcher mit 4,5 mm Durchmesser vorgesehen, sollte aber auch mit doppelseitigem Klebeband halten.
Beim zusammenbauen darauf achten, daß die Seitenteile und Halter beim einstecken noch nicht mit der Grundplatte fluchten, erst beim herunterschieben sind die Teile dann bündig. Sollte das zusammenstecken schwer gehen, einen kleinen Hammer und ein flaches Stück Kunststoff/Holz oder einen Schonhammer verwenden und im Bereich der Grundplatte vorsichtig auf den Halter/das Seitenteil schlagen.
Wichtig für den Druck: Die Schichthöhe wurde mit 0,2mm geplant und so sind auch die Bauteile dimensioniert. Wollt Ihr andere Schichthöhen verwenden, könnte es sein, daß das Stecksystem nicht mehr funktioniert.
Simple holder for rubbish bag rolls to be plugged together. There is a choice of two side parts and two holders. The high holder (holder high edge.stl) should be used when attaching the holder to a cupboard door so that the roll does not fall off.
You need the base once, a total of two pieces of the side parts (solid and/or open) and a total of eight pieces of the holders (holder and/or holder high edge).
Two countersunk holes with a diameter of 4.5 mm are provided for fastening, but should also hold with double-sided adhesive tape.
When assembling, make sure that the side parts and the holder are not flush with the base plate when they are inserted, they will only be flush when they are pushed down. If it is difficult to put the parts together, use a little hammer and a flat piece of plastic/wood or a soft-face hammer and carefully hit the holder/side part in the area of the base plate.
Important for the print: The layer height was planned with 0.2mm and the components are also dimensioned this way. If you want to use other layer heights, it could be that the plugging system no longer works.