1 / 2
Aluminum Extrusion Corsi Rosenthal Air Purifier — zdjęcie 1
1 / 2

Aluminum Extrusion Corsi Rosenthal Air Purifier

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

An air purifier in the style of Corsi Rosenthal boxes.

Ocena
0 / 5
Polubienia
24
Pobrania
34
Wydruki
0
Wyświetlenia
1573
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

CORSI-ROSENTHAL AIR PURIFIER

Bill of Materials:
360mm 2040 aluminum extrusion x8
400mm 2040 aluminum extrusion x4
M5 x 10mm button head hex screws x24

M5 sliding T-slot nuts x24
M5 x 16mm self tapping screws x 16
M3 x 17mm hex cap screws and hex nuts x8
14 inch x 14 inch x 1 inch air filter (MERV13) x4
3/4 inch wide x 1/4 inch thick foam weatherstrip x19 feet
120mm PC case fans (ex. Corsair SickleFlow 120mm) x4
120mm fan grille x4
4 port fan hub
5.5mm x 2.1mm female DC power port x1
12V DC power supply (10 watt or greater) x1

3D Printed Parts:
Corner bracket A x4
Corner bracket B x4
Bottom panel A x2
Bottom panel B x2
Fan panel A x1
Fan panel B x2
Fan power panel x1
Panel support x4

Assembly:
Using the aluminum extrusions, M5 screws and T-nuts, and printed corner brackets, assemble the box frame as per this diagram. Green bars are the 360mm extrusions, red bars are the 400mm extrusions. Make sure each side is as square as possible. HOWEVER, be sure to insert the bottom panels and the fan panels into the aluminum extrusion grooves prior to complete assembly of the frame!

Each panel has a small hole in one corner, which is used for bolting to the panel support piece. These holes should be oriented so they all point centrally. You can then join the panels using two panel support pieces on the top and bottom to create a sandwich. Secure into place using the M3 screws and hex nuts.

Once the panels are in place and secured, and the box frame is completed, you can mount the fan grille and PC case fans to the fan panels using M5 x16 self-tapping screws. Make sure the fan is oriented to push air out of the box (so that room air is pulled through the filters, into the box, then out through the fans).

Secure the fan hub centrally. Plug the case fans into the hub. Insert the female DC power port into the panel and secure. Solder the black wire to the negative terminal of the DC power port. Solder the red wire to the positive terminal of the DC power port. All other wires are unnecessary and can be ignored.

Apply weather strip to each side of the box frame where the filters will be inserted. Install all 4 filters. Plug into your DC power supply and turn on!
 

Affliate links to items I used in my build (I may earn a small commission via these links):

360mm 2040 aluminum extrusion 
400mm 2040 aluminum extrusion 
M5 x 10mm button head hex screws 
M5 sliding T-slot nuts 
M5 x 16mm self tapping screws 
M3 x 17mm hex cap screws and hex nuts x8
14 inch x 14 inch x 1 inch air filter (MERV13) 
3/4 inch wide x 1/4 inch thick foam weatherstrip 
120mm PC case fans (ex. Corsair SickleFlow 120mm or similar) 
120mm fan grille 
4 port fan hub 
5.5mm x 2.1mm female DC power port 
12V DC power supply (10 watt or greater) 

Tagi