1 / 6
Dan Pistol (Beta) - Quality of Life improvements — zdjęcie 1
1 / 6

Dan Pistol (Beta) - Quality of Life improvements

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Updated some of the files from original to improve operation out of the box

Ocena
0 / 5
Polubienia
32
Pobrania
77
Wydruki
0
Wyświetlenia
780
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Outdoor Toys
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

This is not a bad blaster when you get past the fact that it's still labeled as in beta.  I especially enjoy the mag release mechanism, and the ability to use either angled or straight magazines.  If you have small hands I might recommend a different one though - this thing is just massive.  With all that said, if you are here it's because you have one already and want to make it better.  Read on…

Recommendations:

  • Recommend get a slightly heavier spring for the trigger than is provided, but be careful it isn't too long (or too heavy) or you'll have issues getting the catch to disengage
  • Many of the DanPistol parts can be printed at something like 3-5 wall loops, 25% infill, and .2 mm layer height. I did not find print instructions for the parts so had to guess.  But I do recommend print the turnaround, the catch mechanism, and definitely Catch 3_1 at 100% infill.  If you don't print Catch 3_1 at 100%, it will not last long.
  • The assembly video recommends gluing the plastic tube to the turnaround, but I have not found it necessary.  Especially when using my modified version of the frame piece, the glue is not required.  The x-ring holds the air very well already without putting glue in here, and the increased height of plastic in front of it in the modified frame_front is more than ample to hold it in place.  If you have compared both with & without and have FPS data, I'd be interested.
  • This should go without saying in this hobby, but DO NOT DRY FIRE this blaster.  The printed parts will not long withstand the repeated impact, no matter how you print them.
  • Recommend printing the “impact” parts that are part of the firing mechanism in a more durable plastic than PLA - PETG or something stronger preferred and will increase the life of these parts.

Modified files:

  • Clamp: Even with the flat part on the catch pieces correctly oriented, I had issues doing the assembly.  The clamp kept colliding with the catch assembly and preventing the front assembly from being attached to the back in the last couple of steps.  I adjusted the clamp here to remove some of the volume near the top which now should prevent collisions and ensure easy assembly every time (for example, if swapping out the spring). 
  • Catch 3_1: More issues with it priming.  The channel in the original file is not deep enough to retain the spring, and depending how you print it, it is not strong enough to withstand firing too many times.  The channel is especially not deep enough once the screws are tightened - the ends push through the nuts, and push the spring out of the channel.  Made the outer edge protrude a few more mm to improve spring retention.  Print this part at 100% using concentric patterns all the way through for increased strength. Consider this part a consumable as well, and have some extras on hand for a game.  DRY FIRING will decrease life of this part.
  • Catch 3_2: I had issues with the catch often failing to engage when primed.  I noticed that the hole in catch_3_2 seemed to be a little too narrow.  I made it slightly wider (1 mm or so) and that appears to have solved this for me.
  • Frame_Front: In the original file, there is a slight dip from the interior of the clear plastic tube (air chamber) down to the slide part of the frame front, along which the spring and plunger mechanism travel.  I noted the spring would often bind on this while priming.  I adjusted this so that the slide area in front of the plastic tube is the same height as the ID of the plastic tube, giving the spring/plunger mechanism effectively a continuous smooth surface along which to slide during priming & firing.  I've noted no further issues with spring binding.
  • Slide_Front: This modification is more cosmetic than anything, but this blaster is already so enormous, I won't be putting anything on the bottom rail.  I removed it to reduce that little bit of weight.  I also removed the parts of this piece that jut out on either side around the aluminum bars.  The last thing this blaster needs is to be even wider.  I recognize that part of this was for retention of the slide_rear pieces, but in my testing, I have found the contact afforded by this new mod to be sufficient.  I did add some volume here to increase the contact between the front & back, which also helps.

Print Instructions:

I printed all of these at 5 wall loops, 25% infill, .2mm layer height, with the exception of the catch piece which I printed at 100% infill. All printed in PETG.

 

The last couple pictures in the series here show some failure modes of the original Catch 3_1 part.  In blue, original piece, catastrophic failure when not printed at 100%.  In black, original piece, printed at 100% using monotonic pattern.  You can see the bouncing of the spring out of the channel is chewing up the channel guides, in addition to the piece cracked all the way through.

 

All of these mods work pretty well in my early testing, but will need some live game play to fully test.  Please send your feedback & thoughts and I can adjust accordingly as well.

 

Update 5/1/2025: added modified version of Catch 3_1.

Tagi