ChickadeeDo (Chickadee Condo) Birdhouse
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
We're improving Black Capped Mountain Chickadees habitat. This birdhouse had 3 new fledglings for 2026!
- Ocena
- 0 / 5
- Polubienia
- 4
- Pobrania
- 27
- Wydruki
- 0
- Wyświetlenia
- 139
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Outdoor & Garden
- Licencja
- Creative Commons — Attribution — Noncommercial — NoDerivatives
We're working on attracting Black Capped Chickadees to our little bit of heaven. I roughly based this design on recommendations for sizing. I read that chickadees also like old stumps or trees with access holes, so I fired up Shapr3D and did my best to make this house look like a log. There are four pieces; the main log, the roof, the address plate and the fixing plate (for attachment to fence or other structure. I placed ours about 5 ½ feet off the ground, east facing over an open area in front.
2026.04.17: I added a fixing plate to mount the condo to a metal post (using zip ties around the post.)
2026.06.16: We were able to watch 3 chickadee fledglings make their first flights out of the condo. The family of 5 hung around for a day and then they were off for new adventures and more food. After departing the nest I took the house down, removed the nesting material and gave it a good disinfecting scrub. Chickadees don't usually use the same nest twice because of potential disease. We're hoping a good scrub, and moving to a new location, will improve reuse next season. Also, taking the house down prevents hornets/wasps from inhabiting the space.
Printing/Assembling
I used an OPXL5H with .6 nozzles and .32 fast layers (although for the address plate I used .4 nozzles and .2 layer height)
I used PETG from various manufacturers (brown for inner and gray for the outside perimeter)
I used 4 x 4mm voron inserts (in the log) and 4mm stainless pan head screws to attach the roof to the log
I printing the outside of the log with fuzzy perimeter to more simulate a rough log
I attached a small strip of self adhesive velcro (fuzzy half) to the inside of the house from the access hole down to the inner base. My thinking is the PETG is too slick for the fledglings to climb up. I guess we'll find out.
Hints/tips
Since chickadees nest in older or rotted trees, they have a need to excavate/hollow out a potential home before habitation. We put a handful of wood shavings in the bottom of the birdhouse to give them something to remove. Gives them a sense of home ownership!
Each of the pair of chickadees has a need to impress the other with the house they think is best, so we like to place 3 or 4 houses around the lot to give them a choice. It's really fun to watch them flit between houses, and hollow out each, when they're shopping for a residence.
We found they preferred a post mount about 8 feet off the ground. We picked a post next to a large spruce as it gives them a place to perch before/after flying to/from the house. They're secretive and fast to prevent other birds from knowing where they live.
The chickadees picked the 3D printed house over traditional cedar houses, we think it's because the 3D house is deeper. For next year I'm going to 3D print 'basements' for the cedar houses.
It appears chickadees don't use the same house consecutive years (disease), so we'll scrub the existing (winter) and move to slightly different location to see if that helps provide a sanitary and reusable home.
The entry hole size is very important (1 1/8") as we've watched scavenger birds poke their beak inside the hole, but can't get in (except wrens might.)
Place the birdhouse so the prevailing wind blows on the back of the house. In other words, the entry hole is downwind.