Unifi UCG Fiber 19" Rack mount with PSU mount, Keystones and slicer mods for Front Power Cable
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
This is a remix of different projects to combine UCG-Fiber mount with front connectors and the PSU holder.
- Ocena
- 0 / 5
- Polubienia
- 15
- Pobrania
- 265
- Wydruki
- 0
- Wyświetlenia
- 1897
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Electronics
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
EDIT Jun 2025: Updated models 9 Jun 2025. Improved the power cable cutout and increased the rigidity of the models in the mid section where they join and across the PSU holder.
EDIT 2: Nov 2025. I am not able to do more mods on this. A helpful contributor @FrankSteinba_2875151 has added a remix of sorts with a bridge to stop the tall ‘arms’ wobbling during print. If that is a problem for you try his stl which I have added in the file section.
I apologise that this is not as well layed out as my normal models however I had to create this as a Frankenstein from other STL to form what I envisaged. I'm a novice CAD operator and it's often a brute force outcome not elegance!
I do have an alternate I uploaded for mounting into a Rack brush panel. It's complete design and much more rigid for a 19" setup than this one. It does require a specific brush panel, or some quick metal work of the common style to make it work.
https://www.printables.com/model/1313599-unifi-fiber-and-psu-19-rigid-metal-mount-using-bru
Please follow my instructions - they are essential and most questions I am sent are in this section - you need to read it!
This is a 19" Rack mount for the UCG Fiber and its PSU with some keystone holders.
It needs to be rigid so I would not use PETG. PLA or perhaps ABS or even a PLA-CF or GF.
I have combined 2 other projects and modified them to achieve my needs of a rigid UCG Fiber holder that allows front fit of the power cord, holds the PSU and has greater rigidity. I printed a number of variations and most sagged/twisted due to deficient support.
Thanks to the original designers for their precise work - great models with nice fit, and I'm pleased with my outcomes that add some extra benefits.
Original Models
Superpilot for the PSU and keystone mount I modified to fit the UCG Fiber mount I used in a 19" format.
https://www.printables.com/model/1264215-ucg-fiber-keystone-and-power-supply-1u-19-rack-mou
Mixmeister for the UCG Fiber mount I used and have altered to fit the power cable more easily.
https://www.printables.com/model/1229104-unifi-ucg-fiber-rack-mount-19-inch
Keystone blanks I found fit nicely:
Rtdog19
https://www.printables.com/model/557655-keystone-blank
Printing:
PLA+ is rigid and still a good option. I'm not finding mine heating a lot in general use, so I think the claims for PETG being essential by some need not be applied for this router model.
I printed at 0.2mm to produce the hexes and curves smoothly. The fit has some play and should be ok if your printer is not perfectly calibrated.
You will want 3 screws/nuts to join the mounts and 8 small screws +/- heated inserts for the rear covers.
Note: If you use a patterned build plate like mine with Carbon Fiber… be sure to align the 2 halves on the plate in the exact same orientation so the pattern is continuous across the full face.
Assembling the 2 halves:
1. Use about 120-320 grit sandpaper on flat surface and gently sand the faces that screw together until both fit flawlessly with no visible join. Be careful not to round the front edge… keep it sharp.
2. I advise gluing the halves together as well as the screws to clamp in place. Use a flat surface to ensure the halves are precisely aligned and the front face pulled tight with no gap.
Glue increases rigidity (the screws can act as a fulcrum and the front flexes open).
Some sharp-edged tape (even sellotape) on the front at the interface edge to collect excess glue and a razor run along to remove dried excess does wonders.
Some instructions regarding the .3mf files:
I made some final revisions using slicer negative volumes to improve the power cable access on the Fiber and the PSU so it can be rear mounted through the holder.
Open the .3mf files as projects to ensure you have these associated changes and print as the parts are shown. They can be moved around if you have larger plate than my MK3s :).
Note: in the photo the power lead from the PSU runs neatly at the front into the Fiber mount.
To achieve this, on the side of the Fiber holder where the screws fit, use some snips to cut a hole from the hex shapes at the front near the power cable cutout. This is to allow the power cable head through to run down beside the Fiber and out the front to the connector. A small file can help too to reduce the sharp edges and clearance. I did it this way to avoid needing supports and haven't altered the model to include some final dimension changes I made by filing. You just want the cable to fit nicely so you can slide it when the Fiber is locked in place and not have too tight a bend on it.
This then enables you to have the very short cable run you see in the image, and store the rest of the cable at the front of the PSU in the holder (Instead of forcing the cable down the side of the holder.
I used threaded inserts for m2 screws to secure the back of the PSU and Fiber however you can directly screw with fine screws.