1 / 8
Unifi Fiber and PSU 19" rigid metal mount using brush plate. — zdjęcie 1
1 / 8

Unifi Fiber and PSU 19" rigid metal mount using brush plate.

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

I built a reinforced 19" Rack mount for my UCG Fiber and its PSU using printed parts bonded to a 19" brush plate.

Ocena
0 / 5
Polubienia
5
Pobrania
19
Wydruki
0
Wyświetlenia
414
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Computers
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

This is a UCG Fiber mount combining printed components and a common 19" 1RU Brush plate or blank.

This mount is more rigid than others, avoiding sagging or flexing. It incorporates a PSU mount, some keystone locations, a side entry and channel to fit the power jack when sockets are front mounted, and a cutout to allow the PSU power to be connected from the rear.

It will require a grinder and basic metal work unless you have a brush plate that has a single 90 degree bend top and bottom*. Alternatively, a 1RU blank with cutout of the front to your desired size for the Fiber will suit.

*See the close up image of my brush plate - noting it does not fold right over… it's just a “U” with 90 deg bend top/bottom like any blanking plate. 
Some brush plates are folded right over to create a channel for the bristles. You can cut the edge off to remove the channel as I did, or if you have a blank plate, you can measure and cut an opening you like. 

There are brush plates which are the “cheap” versions which have only the 90 deg bend (no channel) and crap bristles - these are perfect for this! I couldn't find one local so I just made the two simple cuts to make mine suitable.

Suggested parts:
1. Printed UCG mount, PSU mount, and rear cover for each.

2. 1RU Brush Plate or Blank Plate.  (Ideally a brush plate with single 90deg fold top & bottom not a 180 fold (channel) … no metal cutting required)

3. 8x heated inserts and m3 screws for the rear covers; alt of m4 screws direct to plastic.

4.  M4 screws and heated inserts to screw together the main body parts. This is not essential but can assist when gluing. Screws/nuts of any fitting size will do.

5. Epoxy adhesive or other suitable strong, permanent and rigid adhesive for metal and plastic adhesion. Epoxy is good because it fills space between the printed body and metal plate which is what we want.

Tools for cutting the brush plate or Blanking plate (if required):
1. Grinder with thin metal cutting disc (or a milling machine :P). 
2. Metal file(s).
3. Sand Paper
4. Masking tape
5. Primer and paint

PERSONAL PROTECTIVE EQUIPMENT - EYE, HEARING, GLOVES/APRON IF REQUIRED TO PROTECT FROM HOT METAL. KNOW THE TOOLS YOU ARE USING AND KEEP SAFETY GUARDS IN PLACE. YOU ARE RESPONSIBLE FOR YOUR SAFETY.

Other tools:
6. Side cutters - needed to trim the entry for the DC power plug when having sockets to front.
7. Clamps to hold items together while adhesive sets.
8. normal tools for tidying up your prints.
9. Sandpaper - about 80 grit, and a very flat surface.

General Summary:
Purely printed versions of a UCG Fiber mount I tested and further modified were all designed for 10" rack and lacked rigidity for 19". They either bent, warped or just sagged right across the span… it wasn't a case of bolstering one spot. I'm so thankful for the designs done though because I'm not expert with CAD and they offered a great start for my amalgamated design. 

There is still has structure that may not be essential for this mounting method. It's strong, and it works though!

Thanks to the below Makers for the precursor designs. Check out there pages for a pile of awesome designs. Very inspiring pair of makers! 
Superpilot
Mixmeister

Basic Steps:
The 3mf files I include have a negative volume so open as a project. The cylinder in place is to remove a section of the PSU backplate so the power cable can be inserted if you want the AC power from the back. 

1. Print the 4 main parts needed. You may want to split them to print individually - especially if you have a carbon fiber or other patterned sheet where it is important to align the pattern for a seamless look. 
I used a brim for the main body because I wanted zero warping. 

2. Where the front DC power plug fits, use your cutters to remove some of the hexagons to create space to insert the plug through. This allows the power cord to be bundled in front of the power brick and minimal cable (See images).

3.  Using your sandpaper and a hard flat surface, carefully sand the mating surface of the 2 body parts. Use movements toward the visible face of the parts so the edge stays razor sharp with no chipout/fraying. When the whole surface has sanding marks you have it dead flat and when glued should have the best possible join.

Note: Image showing elephant foot causing opening between parts. This is why you sand.

4.  Prepare your brush plate or blanking plate. If you need to grind off the channel edge or cut out a face section be sure to cover the plate in painters tape or similar to minimise paint damage. Use files, grinding wheels and such to clean up the edges for safe use in your rack.

*Be sure to test and adjust for fit of printed parts.

(a) Degrease/clean, Sand, Prime and paint to a beautiful finish
(b) clean and prepare for adhesive

5. Glue the main body parts to the metal plate. Use some wood to achieve even light clamping pressure.

Advice: place epoxy along the upright edge of the metal plate - not on the flat section with the cutout. It will flow somewhat into the flat section but not leak out and make your part look like crap with excess glue runout. Also glue the 2 main body sections together if not already screwed.

6. Once cured insert heated inserts for the rear covers, or thread them with your direct screws.

Done… mount in your rack and enjoy it. 

I found that the below keystone blank by Rtdog19 works well:
Keystone-Blank by rtdog19 | Download free STL model | Printables.com 
 

Tagi