Rx 9070 XT Reaper 120mm fan shroud
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Fan Shroud that fits 2 x 120mm fans on the Rx 9070 XT Reaper.
- Ocena
- 5 / 5
- Polubienia
- 21
- Pobrania
- 136
- Wydruki
- 0
- Wyświetlenia
- 4189
- Oceny
- 1
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Computers
- Licencja
- Creative Commons — Attribution
Rx 9070 XT Reaper 2x120mm fan shroud
Fan Shroud that fits 2 x 120mm fans on the Powercolor Rx 9070 XT Reaper.
Important: This shroud will only fit with pcie-raisers, vertically mounted cards!
The goal with this shroud was to reduce noise, I want quiet gaming. Don't except better cooling performance with this mod, just quieter cooling.
I've used 2 x Noctua A12x15 fans to keep the height down. Unfortunately I forgot to measure the new total height of the card but I think it ads about 1-2 mm of height.
The model is split into parts that will fit on a 180x180mm print bed. Parts may be glued together, but it's not really necessary as the card and fans will hold everything togheter
You will need to remove the heatsink to remove the old fan shroud and fans. But once you done that this shroud is designed to be removable without removing the heatsink from the card.
I hope this description covers everything, if you have any questions please ask in the comments. It would be fun if somebody else got some use out of this model.
Fan duct:
The model also includes a fan duct to get cold air from outside the case. The shroud can be used without this. The included fan-duct fits with the Loque Ghost S1 case. Because of the design of the ghost s1 the corner needs to be cut of, a version without the corner for the ghost s1 is included. There is also one complete duct for other cases.
If you want to use the duct with another chassis you can just extend the edge in you favorite cad software to the right height for you case. (or leave a comment and I can make a adjusted version)
Needed parts:
Fans:
2 x 120 mm fans of your choice (I used Noctua A12x15)
Fan connector:
Mini 4Pin to 2 x 4pin PWM connector ( I used this one https://www.aliexpress.com/item/1005001579112907.html
Screws:
8 x M2.5x25 (x30 works but will portrude on the underside)
6 x M2x5 (x8 or x10 would also work but will portrude on the underside)
Brass inserts:
8 x M2.5L3 (or L4)
6 x M2L4
3D-printed parts:
5 x 120mm_fan_mount_9070xt_reaper
1 x 120mm_fan_mount_9070xt_reaper_small
120mm_fan_adapter_9070xt_reaper_part1
120mm_fan_adapter_9070xt_reaper_part2
Optional fan duct:
120mm_fan_duct_9070xt_reaper_part1
120mm_fan_duct_9070xt_reaper_part2
120mm_fan_duct_9070xt_reaper_part1_ghost_s1 for the Ghost S1 instead of part 1
Optional:
Zip-ties for cable management
Print settings:
- PETG or PLA
- 30% Infill
- 4 perimeters