1 / 9
Camp lantern LED — zdjęcie 1
1 / 9

Camp lantern LED

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Retro design lamp, using two power LEDs and controlled by ATtiny85 microcontroller.

Ocena
0 / 5
Polubienia
25
Pobrania
81
Wydruki
0
Wyświetlenia
496
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

--------------------------------------------------------------------------------------------------------------

Update 01.07.2025 - I've replaced zip package with GERBER files, since I've just realized that there where missing files for drill holes. Now everything should be fine. My apology for any inconvenience.

---------------------------------------------------------------------------------------------------------------

 

This is a neat LED lamp styled like an old hurricane lantern. It's driven by two power LEDs (star type), controlled by ATtiny microcontroller and powered by 18650 Li-ion battery. The project involves some soldering, programming microcontroller and preparing or ordering a PCB (all nessearly files included). Of course You don't have to do it this way. I provided .step files so it's easy to modifing for Your needs. Like ie. removing all the electronic and using a simple on-off switch instead. Below I'll guide You through the whole porces of how I did it. 

 

Hardware parts

  • Bolts M2x4 - 3 pieces
  • Bolts M4x10 - 8 pieces
  • Heated inserts M3x5x4 - 8 pieces
  • Battery contact (spring plate) for 18650 cell - 2 pieces
  • Battery 18650 Li-ion
  • PCB (either order, etched or perfboard)
  • LED 1W - 2 pieces
  • Charging module for Li-ion battery 
  • ATtiny85
  • Transistor IRLZ44N (not ideal for this application, mainly because it size, but it works and this is what I had in stock)
  • Tactile switch 6x6mm
  • Resistors: for LEDs - 4,7ohm 0,6W (at least, preferably 1W) - 2 pieces; for transistor 330 ohm (this depends on transitor You use)
  • Capacitor 100nF 
  • Conncetors - 2 pieces
  • Some wires
  • Epoxy and/or CA glue
  • Heatsink - 3 pieces (not necessarily, but recomended) 

Regarding the PCB, as I mentioned there are a few ways to do it. You can get it manufactured for You using GBR files (in zip package). This is easiest since You don't have to care about holes and switch alignment. If You would like to some DIY, there is a PDF with traces, that can be used for PCB etching. The last option is making it on prefboard. For those who choose this option, below is schematic and sketch with holes and switch position.

For charging module, I use typical one for one Li-ion cell. I think they are all similar, since I've order it a few times from different vendors and always get the same, but for the reference here are the main dimensions of what I use:

The microcontroller I use is ATtiny85 but I think the other from the “family” should work as well (so 25/45/13). It was programed using Arduino IDE. Of course I provided as well the sketch for programing.

Print settings

  • Main body
    • Layer height 0,08mm
    • 3 walls
    • Brim
    • Arachne mode or Detect thin walls - without this the included supports will not print
    • Top surface pattern: Concentric
  • Base
    • 3 walls
    • Sacrifical layers for counterbore holes (it's a setting in OrcaSlicer, if You don't have) this in Your slicer just use supports under those holes 
  • Lampshade
    • Spiral vase mode
    • Outer wall 0,8mm 
  • Handle
    • Print in TPU
  • LED holder
    • Print in some heat reasistnat material like: ABS/ASA/PA
  • Button cover
    • Layer height 0,08mm - not necessarily, but it will make it nicely aligned with the main body

For the settings and parts not mentioned, just use Your standard profile. All parts files are in the proper printing orientation. You need to print only one of each part from the root directory.

Assembly

Ok, now the fun part 😊. The main body it's designed with supports already. There is also version wihtout it but I don't recommended it. I've made a lot of tests and none of the slicer generated supports give a satisfying effects. I admit that removing supports designed by me, might be tedious and the inner surface won't be great, but it prints well, don't waste too much material and the outer surface is really nice. So, after the print and removing the brim it will look like this:

All thin walls in the bottom needs to be removed. Just use side cutters and knife to do the job. It doesn’t have to be perfect, no one will see this 😊 On the main body front You need to as well cut the opening for the button. After this step it will look like that:

Next install the heated inserts. At this stage it will be good to solder all the electronic components. Resistor for LEDs are soldered directly to their PCBs. Then solder the wires, connect those two LED in parallel and crimp in one connector. I put a small heatsink on the back of each LED. After that slide them into LED holder. Sometimes it goes in tightly and sometimes loose; to be sure it stays in place I put few drops of CA glue on the rails. Here are LEDs installed in the holder:

Now install PCB into the base using two M2 bolts. Then it's time for the button assembly. There might be needs for some adjustment depending on the height of tactile switch. So, bolt the base and main body front together and slide the assembled (but not glued yet) button cover.

Hold on the button cover and push on the inner part to check if it's clicking. If the switch is always pressed in, then sand the Button pusher2 part, the side that is in contact with the switch. If it's the opposite, the switch isn't pushed at all, You can just put small piece of tape on it. Of course, in both cases You can just adjust the Button pusher2 and reprint it, since it's a small part. Although it might sound like hassle, but for all lanterns I've made, only for one of them I have to do the adjustment (thickening it by sticking some tape). Nevertheless, it’s good to check that before gluing button assembly together, which is the next step. First use some CA glue to join Button pusher1&2 together inside button cover.

Be careful not to glue them to the cover itself. Take this assembly place in the main body frony and glue the button cover to the body with epoxy glue. It's good to use some tape for tempotaliy attached those to pieces together while putting the epoxy. Again, take care to avoid gluing button cover to the button pusher.

When the epoxy is cured, place lampshade and handle into one main body half and cover with the other half. Install the M4 bolts but do not tight them yet. To properly aligned the main body assembly with the switch on PCB, place the base inside the body and find the position when the button is working properly. Now install and tighten two M4 bolts on the base on the side that is closer to the button. Then install and tighten the other two bolts on the base. Check again if the button is working and now tighten all the screws on the main body. Remove the base from the main body (I promise it’s the last time 😊). Put the LEDs inside the lampshade align with the notch and secure with M2 bolt.

Place the battery inside the base and connect it to PCB. I sticked heatsink on the charging module since it get quite hot will it's charging the battery.

The only thing left is to connect the LEDs, reassemble the base…

…and the lantern is ready. Enjoy :D

Tagi