NTC 100k 3950 Glass Thermistor Chamber Sensor Mount - Straight Remix - 2020 Extrusion
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A remix of the chamber thermistor mount with the wire and thermistor openings opposite each other instead of adjacent.
- Ocena
- 0 / 5
- Polubienia
- 16
- Pobrania
- 105
- Wydruki
- 0
- Wyświetlenia
- 484
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Voron Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial
I redesigned the chamber thermistor mount to have the thermistor and wire outputs be opposite instead of at a right angle to each other. This is better for my use case, as it allows me to mount it on the bottom back extrusion of my Voron 2.4 while keeping it as far out of the way as possible.
Use an M3X10mm socket head cap screw for the standard version, or an M3X8mm for the 1mm channel version. Both use an M3 drop-in t-nut to mount.
Here is a link to a pre-wired thermistor: https://amzn.to/3I5DiVO (affiliate link). I have not used these myself, but they should fit as the two leads from the thermistor are fairly long before they join together at the thicker wire. They also come with a standard XH 2.54mm connector and should plug right into the main control board. This is the easiest wiring option.
I made the channels leading up to the thermistor angled inward, in an attempt to minimize movement of the thermistor.
Other improvements include the rotation prevention features on both parts. These are designed to fit together in either orientation relative to the 2020 extrusion. They also have a slope angle of 45 degrees so they can print without supports. I have used a tolerance of 0.15mm, which could be a bit tight for some printers but should prevent any rotation.
The step file is included for any CAD users who wish to easily modify the design.
Lastly, I vastly improved export quality. I exported my STLs at maximum resolution, versus the original which had only about 5 facets per 90 degree radius and only 13 sides to a circle. This does increase file size, but is worth the tradeoff.
Edit 6/18/25: Increased channel depth and width to 1.6mm to allow more room for wires and reduce the gap between the 2 plates. I used insulation stripped off of some 26 AWG wire to cover the bare wires of the thermistor within the block. The insulation has an OD of 1.5mm, which should fit snugly within the block. Then, outside the block where the 2 thermistor leads poke out, I soldered on extension wires and added heat shrink.
I increased the size of the keying features for better printablity, and added a Voron-style bridgable countersink hole to remove the need for any support.
For printing, I increased minimum layer time and decreased minimum layer speed to allow the keying features more time to cool. I also added a small 7.5mm high shape in the slicer to help increase the final layer times above 20 seconds. This should not be necessary with PLA, but I printed these in ABS which requires a low cooling fan setting. Apply your own expertise, as my ABS prints still came out far from clean.
Edit 6/21/25: Added a second version of the top block with a shallower 1mm depth instead of 1.6mm for all wire paths. This allows thinner wires less room to shift around, with the goal being a slight clamping force on the wires within the block. The other benefit is that this uses a shorter M3X8mm screw, of which I had several left over from my Voron build. This version is closest to the originally published model.
