Shower curtain rod (25/22 mm) holder
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A three-piece friction holder for an expanding shower curtain rod (outer diameter 25 and 22 mm), with TPU wall pads.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 12
- Wydruki
- 0
- Wyświetlenia
- 82
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Bathroom
- Licencja
- Creative Commons — Public Domain
FreeCAD file is also provided.
This model fits expanding shower curtain rods with an outer diameter of 25 and 22 mm. The parts in contact with the walls should be printed in TPU to improve grip and require less force. PLA should be sufficient for the other parts.
Prints well with a 0.4 mm nozzle on an Ender 3 V3 SE. Print settings aren't too critical, but there are a few recommendations I would make, see below.
Shower curtain rod holder-Holder22mm
Shower curtain rod holder-Holder25mm
These are the holders for the tubes, one of each is required. These parts should be printed in PLA or any other hard material. Print time is about 40 minutes.
| Setting | Value | Remark |
|---|---|---|
| Layer height | 0.28 mm | This is purely functional, and the slope is quite high, so layer height can be too, but decrease if you want a smoother finish. |
| Top layers | 6 | The top and bottom are under compressive load, and the top is in contact with the tube end, so best add a few more layers here. |
| Bottom layers | 6 | |
| Top/bottom pattern | Zig zag | The tube ends will press onto the top layer, so probably a bad idea to do a concentric top! |
| Bottom layer initial pattern | Concentric | Personal preference - usually prints a little faster too. |
| Infill density | 20% | This part will be under load in different dimensions, so might as well increase this. |
| Adhesion | None | |
| Speed | 90-45 mm/s | Or as dictated by material & printer. |
Shower curtain rod holder-Foot
Foot for the two holders, so two required, and print them in PLA as they're load carrying. Print time is about an hour each.
| Setting | Value | Remark |
|---|---|---|
| Layer height | 0.28 mm | This is purely functional, so height can be pretty high. The slope is quite shallow of this part, so decrease this if you don't want quite noticeable 'plateaus'. |
| Infill density | 20% | This part will be under compressive z axis load, so don't cheap out on density. |
| Infill pattern | Cubic | A simple stacking pattern should do here, the load is in one direction only. |
| Speed | 90-45 mm/s | Or as dictated by material & printer. |
Shower curtain rod holder-Sole
This part is a bit special as it's printed in TPU 95H. Two are required, and they print at an hour each. They are meant to grip the walls and be compressed a bit, hence the choice of certain parameters.
| Setting | Value | Remark |
|---|---|---|
| Layer height | 0.2 mm | |
| Top layers | 3 | I decreased the top and bottom to provide a little more infill and enable more compression. The top might not look its best, but it won't be visible. |
| Bottom layers | 3 | |
| Infill density | 10% | This needs to be quite low to ease compression. |
| Infill pattern | Gyroid | Perhaps best pick a pattern where each layer is slightly offset, to improve the compressive ability of the model. |
| Adhesion | None | |
| Speed | 60-20 mm/s | It's TPU, lower is better.. |
| Cooling | 25% |