Stepper Motors tooned Cybertruck - multi-part - no support
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A noppo inspired deformed model of the Tesla Cybertruck featuring moving parts, segmented into easy to print pieces
- Ocena
- 0 / 5
- Polubienia
- 6
- Pobrania
- 26
- Wydruki
- 0
- Wyświetlenia
- 160
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Vehicles
- Licencja
- Creative Commons — Attribution — Noncommercial — NoDerivatives
A noppo inspired model of the Tesla Cybertruck featuring an opening hinged rear hatch revealing a small cargo area, as well as working suspension and free rolling wheels. The model has been segmented into easy to print support free pieces. Requires multiple #4 x 3/8" pan head screws (or 4G x 9mm sheet metal screws), and two Chupa Chup plastic sticks for use as axles.
SAFETY WARNING: THIS MODEL IS NOT FOR YOUNGER CHILDREN - SMALLER PARTS MAY BREAK OFF AND BECOME A CHOKING HAZARD. THIS MODEL DOES NOT COMPLY WITH TOY SAFETY STANDARDS!!!!
● Easy to print parts - no supports required
● Designed with colour breaks. Print parts in different colours on single colour printers for a more interesting look.
● Requires multiple #4 x 3/8" pan head screws (or 4G x 9mm sheet metal screws), and two Chupa Chups sticks cut to 63mm for the axles
● In addition to the necessary screwdriver, and cutting blade for the Chupa Chup stick, having some small files can be helpful
The part orientation for printing as per upload is correct. Some parts require a small amount of bridging while printing, though they'll still print well enough without supports. Interconnecting part fit may be tight, depending on the plastics used, or the printer/slicer settings. The tolerances on the tyre/hub combo are important. The hub is intended to be a tight fit onto the Chupa Chup stick, and the tyre needs to also be a tight fit on the wheel. Printing and scaling one tyre/hub combo until the sizing is correct for the axle (before committing to the other three) is recommended. This attention to sizing is also necessary for the hinge part, which may also need to be scaled slightly so that it fits snugly into the canopy part, preferably without jamming so that it can be removed/replaced later if required.
Multiple #4 x 3/8" or 4G x 9mm sheet metal screws are used to join parts throughout the model. All but two are hidden when the buggy is complete. Assembly of the model parts in the correct part order is necessary, though it is a bit of a puzzle that you will need to figure out yourself :) With correctly sized parts, no glue is necessary, allowing for part replacement if any should be required. Often the joining of the chassis assembly to the body assembly takes careful, yet firm pressing to get the parts to mate, which makes assembly less suited to younger builders.
The red brake light bar across the rear of the vehicle is created with a pause/filament swap operation.
Additionally, the parts bodyside, mudguard, and hinge need to be mirrored and printed.
The suspension spring piece will slowly sag if printed in PLA, though it can easily be removed and rejuvenated by carefully running it under (very) hot/boiling water for a moment, and then gently re-aligning the spars. Again, this process is not suited to young modellers.
This vehicle also uses the same #4 x 3/8" or 4G x 9mm pan head screw size featured across my other models, so if you have any left over from another build, here's a chance to use a few more of them up! And finally, if you like the model enough to print it, please consider taking a pic or two, and posting a make. I like those!
Note: Each grid square in the build pics are 1cm