1 / 4
Lucas Distributor Part Number 408945 - Low Tension Insulator Bridge for DVX4A DVXH4A DVX6A DVXH6A DVZ6A DVZH6A. New V2 is ready to fit and use. — zdjęcie 1
1 / 4

Lucas Distributor Part Number 408945 - Low Tension Insulator Bridge for DVX4A DVXH4A DVX6A DVXH6A DVZ6A DVZH6A. New V2 is ready to fit and use.

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Classic car distributor, replacement part. Print your own for the princely sum of 3p instead of £15 to £25 retail.

Ocena
0 / 5
Polubienia
3
Pobrania
10
Wydruki
0
Wyświetlenia
78
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Automotive
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Commissioned by a friend for his Lanchester's Lucas distributor, specifically the DVX4A but the Lucas part number 408945 is listed as fitting all the other distributors shown in the title of this model. Apparently there are a lot of those distributors around in classic cars, so I'm publishing the model here in case it's of use to someone else too.

We don't know yet if the temperature inside the distributor could reach the glass transition temperature of PLA+ which is all I have available, and that's quoted as about 60 Celsius. 

So if you want to try out this part, either check your temperatures, or print it in something that definitely won't melt, hehehe! 

I used 20 walls just to make sure it's all walls, and a 3 line external brim which detaches easily and ensures a clean nozzle. 0.4mm nozzle, 0.1mm layers just to get as many layers as possible. Print with the 2 mounting bolt holes vertical and the flat bottom on the printbed. Designed for this printing orientation so that the continuous circles around the vertical bolts will be the strongest. If you'd like to see what happened to the £25 commercially 3D-printed one that was fitted previously, here's a picture of the failure…

To improve strength for the 3D print, I beefed up the surrounding structure a little, as much as space would allow in the distributor, and also used a hole for the horizontal square-head bolt's shaft instead of a slot. That means it's slightly trickier to mount as you have to take the nut off the square-head bolt to pass the shaft through the hole, but it should make the part considerably stronger.

UPDATED 8/8/2025: The first design attempt left the vertical mounting bolts a fraction short of best position in the mounting plate, so V2 of the STL has their counterbore 0.5mm deeper and this is spot on now, so the original STL has been deleted. Also, the recess for the conductor tab that comes up from below the insulator needed to be shaped exactly to prevent it twisting around when tightening the big bolt, which might have risked it shorting against other components. V2 has an inset to trap the tab and prevent it rotating. V2 has now been fully fitted in the distributor and checked for any fouling against other parts and the distributor cover, and it's all good. So get V2 here now :o)  All printing instructions are the same as before. 

UPDATED 6/10/2025: Has been in place and working fine since the last update. I've had a chance to section the commercially 3D-printed one now and it's pretty shocking - it was done with 0.26mm layers and had 1 perimeter (!!!!!) and the rest was 100% infill. Part of it actually crumbled away as I was lining it up to knife section it.

Please Like this model if you find it useful.

If you REALLY like it, https://www.buymeacoffee.com/gigabeast :o)