Compact Travel Case for Philips Norelco Series 7000 & Newer
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
This is a complete model of a sleek and compact travel case for Philips Norelco Series 7000.
- Ocena
- 0 / 5
- Polubienia
- 23
- Pobrania
- 63
- Wydruki
- 0
- Wyświetlenia
- 845
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Organizers
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Hello Everyone, I hope you are all doing well!
I am happy to share with you all the complete model assembly of this sleek and compact travel case for your Philips Norelco Series 7000 and newer.
This case will allow the user to store the trimmer itself, the small trimming head, all 6 beard/stubble guards, small brush, and charger.
Overall size of the case is 3.900"w x 6.910"l x 1.843"h.
The STL provided will have all components needed for the assembly of the case. I would like to note that all tolerances were +/-.003" to make all parts a snug fit.
I printed the files with the following setting on the PRUSA COREONE:
-Used default .250mm speed print settings
-adjusted the infill to 15% with gyroid pattern
-no supports were needed (depending on your printer, you might need to enable supports for bridging at the corners where the magnet pockets will be made)
For my print of this model, I did a color swap to try and capture Philips logo contrast.
I used the following filaments:
-Overture Matte Light Blue PLA
-Overture White PLA
You can print majority of all the parts on a single bed plate.

I had to print the lettering contrast on a separate plate.

I used a textured sheet to have a nice effect on the faces of the lid, case, and side panels.
If you don't care for the textured effect, you can remove the 4 side plates.
Make sure orientation of the side plates are correct they are .025" thick with a taper. The taper need to be inward. See below.


Once all parts have been printed you will need the following item to build the case:
- 8 magnets (6mm x 2mm thick)
- super glue ( I used Loctite's super glue)
Assembly of the case:
- Identify all side panels with their corresponding side on the case. (Case is symmetrical)
- Starting with one side and only one at a time, apply glue along the perimeter of the recess indentation.

- Then apply side panel, make sure textured side is out if applicable. Lay down one end of the panel to set in place then let the rest of the panel guide itself into the recess.

- Firmly press down on the panel until it sets. Quickly wipe excessive glue if needed.
- Repeat steps 1 thru 4 until all four side panels are installed.
- Get one magnet to install into body of the case. Apply one small drop of glue then press in the magnet into the pocket.

- Repeat this for all four corners.
- Grab another magnet and install into the lid. (prior to installing on lid, verify orientation of the magnet is attracting its partner magnet found on the body of the case.
- Apply a small amount of glue in the pocket of the lid for the magnet then press in the magnet.

- Once all magnet have been install in the lid, you can install the back plate for the contrast of the letting. Apply glue around the perimeter of the recess.

- Apply the back plate and apply pressure, if you added texture ensure it is facing outwards.

- Grab the small printed accents for the letters O, R, and P.
- One by one, start apply them onto the back plate on the main face. Again, verify that the textured face is facing outward.
- Apply a small amount of glue on the back plate.

- Place the accent and press into place for the glue to set in. Repeat this for all 5 accents and you should obtain the following.

- This completes the assembly process of the case. Place your trimmer and accessories in their respective cubby.
Happy printing and I hope this print becomes very useful to you! If you have any questions, please leave a comment. Thank you for your time!
