1 / 22
8" Newtonian Telescope "Leavitt" LITE (Metric) MOD-1 — zdjęcie 1
1 / 22

8" Newtonian Telescope "Leavitt" LITE (Metric) MOD-1

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A new remix from Leavitt LITE Metric with some modifications and new parts, all detailed.

Ocena
0 / 5
Polubienia
21
Pobrania
70
Wydruki
0
Wyświetlenia
787
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Share Alike

This telescope model seemed very interesting, and when I found the lightweight metric remix by @Aurelian_513907, compatible with the Sky Watcher Sky Adventurer GTi Equatorial mount, the same one I have, I decided that this would be my choice.

I chose to print in black PLA made with Ingeo 3D870 raw material from Nature Works because it is supposedly more impact resistant. I used a 0.4mm nozzle with 3 perimeters on all the parts. My Creality K1 Max printer can print the complete parts, without having to divide them into three parts.

The carbons rods are 12mm-outer and 10mm-inner diameter.

As I printed the parts, I noticed some difficulties and opportunities for improvement that made sense to me, but may not make sense to you. In any case, I thought it was pertinent to publish, in case it is interesting to anyone else.

The ATM from which I ordered the mirror suggested that I use a 55mm diagonal mirror, similar to the original Leavitt, and I accepted the proposal, with the advantage of reducing obstruction to the primary mirror.

I will detail the parts that I used without modifications (which must be downloaded from the respective links) and which ones I modified and are available for download here.

Weight (including primary and secondary protective cap, laser and and a 20mm eyepiece): 4100g

 

These parts were printed exactly as found in @Aurelian_513907's metric remix:

  • metric_conversion-LTA.stl (full assemblies)

  • metric_conversion-UTA.stl (full assemblies)

  • metric_conversion-Leavitt_Knob_x8.stl (4 units)

 

This part was printed exactly as found in the @NovelTinker_388837's original model:

  • Leavitt v2 - Focuser grub.stl

  • Leavitt v2 - Collet nut.stl

  • Leavitt v2 - 1.25 inch eyepiece adapter.stl

  • Leavitt v2 - Collet.stl

  • Leavitt v2 - Focuser inner.stl

 

Additional parts, from @dinumas_469178:

 

Parts I modified or created:

  • Segments for attaching dovetail platform (from original metric_conversion-Dovetail_TubeAttachSegment.stl and metric_conversion-Dovetail_SegmentMain.stl)

I had some issues: 

  1. It seemed to me that the screw for fixing the dovetail plate was very fragile, and that any slight tension or bending could break the small plastic pillar at the apex of the part.

  2. I was unable to hide the head of my M5 screws, recommended for the dovetail plate, inside this segment, leaving them exposed inside the "tube", where light would pass through and could eventually generate some artifact.

  3. The distance between the screws on the part was greater than my dovetail plate could tolerate. The screws ended up entering the printed part but at an angle, not allowing adequate fastening with nuts. In my case, the distance between the centers of the screw holes that worked was 19.5mm, compared to the original 22mm, which resulted in a significant difference.

  4. The piece that covers 1/3 of the circumference, with dovetail fastening, had a different finish at the ends than the rest of the pieces, cut diagonally, therefore with only one point for screw fastening.

My solution: a new full-circle piece with dovetail attachment and another one with 1/3 of circumference. I chose to place the larger piece closer to the primary mirror, to help with the stability of the structure, knowing that it is a critical point for the structure to bend due to the weight of the mirror. Therefore, I printed the files Extra ring dovetail 19.5mm type A.stl and Extra partial ring dovetail 19.5mm type A.stl . If you prefer to leave the piece with 1/3 of circumference close to the primary and the full-circle piece close to the diagonal, you can print the type B files. This difference between types A and B occurs due to the normal asymmetry of the pieces:

The result of these modifications:

Files:

  • Extra ring dovetail 19.5mm type A.stl

  • Extra partial ring dovetail 19.5mm type A.stl

  • Extra ring dovetail 19.5mm type B.stl

  • Extra partial ring dovetail 19.5mm type B.stl

 

  • New knob

The metric version provides a triangular-shaped knob with three tips. However, when we use 2 knobs to tighten and fix, when the knobs are aligned with each other, it is difficult to manipulate the one underneath. To avoid this problem, I created a new, similar knob with 5 tips, to be used together with the 3-tips. 

(locking nut unnecessary)

File: Modified knob.stl

 

  • Focuser v2

The original model has a version 2 with changes to the focuser, changing the way the eyepieces are attached as well as the precision of the thread. However, the metric version uses the focuser from version 1. I chose to adapt version 2 of the focuser to fit the metric version. This resulted in the following files:

  • Leavitt v2 - Focuser grub screw panel - METRIC

  • Leavitt v2 - Focuser outer bottom - METRIC

  • Leavitt v2 - Focuser outer top - METRIC (print vertically, otherwise the claws will be extremely fragile; I used brim to strengthen the attachment to the table, otherwise it may fall off during printing; Supports not required)

  • Leavitt v2 - Focuser ring 99.5 (practically the same as the original, but I scaled the dimensions on the X and Y axes to 99.5%, to make it firmer on the thread)

The result:

I can say that the result is a very smooth trajectory to adjust the focus.

 

  • Primary mirror cell

My mirror is 202.5mm diameter and 25mm thick. 

I've read a lot about the advantages and disadvantages of gluing the mirror versus simply gently attaching it to its cell. Regarding gluing, there's debate about how many glue points should be used (3? 6? other?), since thermal variations could somehow generate optical repercussions. Without a clear conclusion, I opted to adapt the primary mirror cell to accommodate some changes, based on several things I researched:

  • Leave a space between the mirror and its base, filling this space with silicone glue.

  • Install safety clips

  • Hexagonal shaped screw cavity to avoid false movement of the screw

  • 203.5mm diameter mirror space

I decided to put glue in the 3 main cavities plus a little on the circumference between the

The clamps are installed on the side of the primary cell using nuts and bolts. In this case, I used an M4 screws with a flatter head so it could be hidden within the clamp itself. It's worth noting that this screw, although an M4, requires a smaller Allen wrench than the other M4 screws to tighten it. I used small 2mm-thick EVA foam strips (1mm also works) glued with cyanoacrylate to the clamp to create contact between the clamp and the mirror. The clamp has a track to adjust its position relative to the mirror, as it shouldn't be used to tighten against the mirror tightly, but simply to hold it in place. 

Print the clips in the position shown in the file to take advantage of the strength of the print lines. I used 5mm of brim to prevent the pieces from peeling off during printing.

There is also a new center finder for the primary cell, with handles to avoid touching the mirror.

Related files:

  • Primary cell (new).stl

  • Primary cell (new) clamp.stl

  • Center finder.stl

 

  • Spider and secondary mirror cell

The ATM that made my mirrors suggested using a 55mm secondary mirror (minor axis), which is smaller than the mirror suggested in the metric version and similar to the mirror suggested in the original version (54mm).

To avoid excessive light obstruction, the center of the spider and the secondary cell were reduced to a 50mm diameter, smaller than the smallest diameter of the secondary mirror, and with thinner spider legs. Additionally, linear cavities were added for silicone adhesion and spacers to maintain a gap between the glass and plastic, with the silicone once again acting as a filler at these space.

I also added a cavity for nylon nuts in the secondary cell to secure the protective cover for the secondary mirror. Use nylon nuts and bolts (they have slightly different dimensions than their metal counterparts) because, if one or another object slips out of your hand, you don't want a metal object hitting your precious primary mirror.

During spider printing, material may build up in the nut cavities. The area may need to be cleaned to properly seat the nuts.

I chose to use an M4 60mm hex-head screw for the secondary mirror, with the head inside the mirror (instead of a locknut). Depending on the friction between the parts, when trying to move the adjustment knobs, the screw could rotate unintentionally inside the mirror. This is avoided with the hex head, without the risk of a locknut unscrewing. In the figure below, you'll see a nut securing the secondary mirror from the outside — FORGET IT! Attaching it will make adjustments during collimation difficult. It has been removed.

The secondary mirror's protective cover is secured with M4 nylon screws, also to prevent damage to the primary mirror in the event of an accident.

 

I also created a center finder for the secondary mirror to help with collimation. Its function is not to locate the center of the ellipse, but rather the center of the major axis, which is adjusted by the spider's central screw. If it is above the target or on the minor axis line, it will be at the center of the major axis. Use whichever model you consider most appropriate. The next step in collimation is to adjust the spider's three peripheral screws to direct the laser to the center of the primary mirror, and then adjust the primary cell screws to return the laser to its origin.

 

Related files:

  • Spider (new).stl

  • Secondary cell (new).stl

  • Secondary cover.stl

  • Center finder secondary.stl

  • Center finder secondary linear.stl

 

  • Laser finder

Instead of using the original model's fixed finders, I opted to create a laser mount that fits onto the dovetail's support pillars. Here, I also used nylon-tipped screws. I offer two versions that only vary the size of the cylinder in which the laser pen is installed. One has an internal diameter of 30 mm (as the picture), and the other 40 mm. The mounting bolts that hold the carbon tube are longer than their adjacent pair.

  • Laser mount.stl

  • Laser mount wider.stl

To keep the laser button always tight, you can wrap a piece of tape around the button or use a clip I made:

Clip to hold down the laser switch. Screw 1 is the longer one (pressing the carbon rod), while screw 2 is the shorter one. This is the 30mm diameter laser mount. For greater range of motion, print the 40mm mount — similar to the standard laser mounts found for sale.

 

  • Nylon Wire Cutter

Screws used in astronomical devices often have a "rubberized" tip to prevent damage to the object they're in contact with. This "rubber" is usually actually nylon. I chose to use nylon-protected screws for the carbon fiber tubes, and also for the screws in the laser finder.
For M4 screws, 2mm-diameter nylon wire works well. The biggest challenge is cutting the wire straight. To do this, I made a cutter to print and use with a regular utility knife. The nylon wire should be inserted into the tunnel until it stops inside the 2mm-deep hole in the wall in front of it. An M3 screw can be used in the tunnel (there is a dedicated hole for this) to hold the nylon wire in place and prevent it from moving. Then, simply run a utility knife along the wall to cut the nylon wire relatively perpendicular to its axis. Do this several times to create several nylon tips, and then carefully glue a small drop of cyanoacrylate to the end of the screws. It's very easy for the cyanoacrylate to seep down the threads, which can make it difficult to screw through the nut later.

 

  • Spacers

After the ATM finished making the mirror, they verified that the focus was at 1020mm, so it's an F/5.1, and each mirror can have its own variations. In my case, the measurements between the parts that allowed for proper focus halfway through the focuser with a 20mm eyepiece were these:

The 40mm on the feet is enough to prevent the adjustment screws from touching the floor.

The 17.5mm measurement was the one I found with good focus halfway through the focuser with a 20mm Svbony eyepiece. Depending on your objective, the eyepiece, or the camera you're using, you may need to adjust this measurement by loosening the screws on the carbon rods and repositioning the UTA piece. This isn't exactly practical to do with a tape measure, so I made spacers to rest on the end of the carbon rod in various sizes to make finding the desired measurement easier. I also made spacers for the 40mm and 160mm sizes to facilitate maintenance. See spacers' files.

Notes:

  • UTA: upper tube section

  • LTA: lower tube section

  • If you do not wish to use the nylon tips, increase the length of the screw by 2mm.

  • All the tunnels through which the carbon fiber rods pass internally are printed very tightly, making tube installation difficult. I recommend using 200- or 400-grit sandpaper wrapped around a pen or cylindrical object to wear down the inner surface of the tunnels until you notice enough friction to slide the rods through manually (eventually inserting the first rods by rotating them), and that they're not completely loose. In my case, I believe everything would have stayed in place even without the fixing screws, but it's best to be safe.

  • Message me if you note fails in description or files.

  • Special thanks to NovelTinker, Aurelian and dinumas for criativity and sharing spirit.

 

Screw Usage

Dimensions

Quantity

Fixing carbon rods to LTA, with 2mm nylon tip

M4 8mm

6

Primary collimation screws (hexagonal head)

M4 60mm

3

For primary cell clips (flatter headed)

M4 16mm

6

Fixing carbon rods to ring dovetail, with 2mm nylon tip

M4 8mm

4

Fixing carbon rods to ring dovetail with laser mount, with 2mm nylon tip

M4 12mm

2

Fixing laser mount without carbon rod

M4 8mm

2

Fixing carbon rods to ring partial dovetail, with 2mm nylon tip

M4 8mm

4

Fixing carbon rods to ring partial dovetail, with 2mm nylon tip

M4 8mm

4

Fixing dovetail mount to rings

M5 14mm

4

Fixing carbon rods to UTA, with 2mm nylon tip

M4 8mm

6

Spider, center screw (hexagonal head)

M4 60mm

1

Spider, peripheral screws

M4 40mm

3

Nylon screw for secondary cap

M4 30mm

2

Focuser grub screw panel (fixing it)

M4 16mm

2

Focuser grub screw panel (grub pressure adjustment)

M4 16mm

2

Fixing focuser outer top to outer bottom

M4 16mm

2

Fixing focuser to UTA

M4 10mm

2

Laser adjustment screws, with 2mm nylon tip

M4 25mm

6

 

Screw Size

Total

M4 8mm

26

M4 10mm

2

M4 12mm

2

M4 16mm

6

M4 16mm (flatter head)

6

M4 25mm

6

M4 30mm (nylon)

2

M4 40mm

3

M4 60mm (hexagonal head)

4

M5 14mm

4

 

Nuts

Quantity

M4

63

M4 nylon

2

M5

4

Update 2026-05-25

Added a Dovetail adapter file (similar to laser mount) in case you wanna use a finder. You will need 2 or 3 pair of M4 screw and nut to hold the finder, and will need longer M4 screw do attach the adapter to the ring and rod (again, similar to laser mount)

In any case, consider having extra screws and nuts.

City view 3km far with 20mm eyepiece while adjusting the focus:

 

Jupiter captured with my telescope (using SharpCap and Astrosurface):

Moon mosaic:

Hope you enjoy it!