Bestway Steel Pro MAX Pool Abspann-Klammer | Plane Sicherung (Öse & Haken)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Bestway Steel Pro MAX Pool-Klammer: Sichert Abdeckplane zuverlässig bei Wind. Mit Öse oder Haken, inkl. Distanzgummi.
- Ocena
- 0 / 5
- Polubienia
- 5
- Pobrania
- 35
- Wydruki
- 0
- Wyświetlenia
- 175
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Outdoor & Garden
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Diese 3D-gedruckte Klammer wurde speziell für die ovalen Stützrohre des Bestway Steel Pro MAX Pools entworfen. Sie ermöglicht es, die Abdeckplane sicher am Poolrahmen abzuspannen, um zu verhindern, dass sie bei Wind verrutscht oder wegfliegt. So bleibt das Poolwasser sauber und ist zuverlässig vor Blättern, Insekten und Schmutz geschützt.
Es stehen zwei Varianten zur Verfügung: eine mit einer Öse für das Durchfädeln von Seilen oder Bungee-Gummis und eine mit einem Haken für eine schnelle und einfache Befestigung. Zusätzlich gibt es eine separate Rückwand und einen Distanzgummi, um die Stützrohre vor Kratzern zu schützen und einen festen Halt zu gewährleisten.
Druckeinstellungen & Material
Drucker: Beliebiger FDM-Drucker
Material: PETG (empfohlen, da es witterungsbeständig und UV-stabil ist), TPU für den Distanzgummi
Schichthöhe: 0,2 mm
Infill: 20%
Stützstrukturen (Supports):
Verwende die Einstellung "everywhere" für Stützstrukturen. Dadurch werden auch die Bohrungen und die Unterseite der Öse sauber gedruckt.
Für die Klammer mit Haken sind Supports ebenfalls notwendig, um den Haken stabil zu drucken.
Hinweis zum Distanzgummi: Das mitgelieferte STL für den Distanzgummi sollte aus TPU mit 100% Infill gedruckt werden. Dieses flexible Material schützt das Poolrohr optimal und sorgt für eine rutschfeste Verbindung.
Pro Klammer-Set (bestehend aus zwei Klammerhälften) benötigst du:
2x M5x20 mm Schrauben
2x passende M5 Muttern
Wichtiger Hinweis: Ziehe die Schrauben nicht vollständig fest! Lasse einen kleinen Spalt von ca. 1 mm zwischen den beiden Klammerhälften, um ein Brechen des PETG-Materials zu verhindern. Die Spannung des Gummis und der Klammer sorgt für einen sicheren Halt.
This 3D-printed clamp has been specially designed for the oval support tubes of the Bestway Steel Pro MAX pool. It allows the pool cover to be securely fastened to the pool frame to prevent it from slipping or blowing away in windy conditions. This keeps the pool water clean and reliably protected from leaves, insects and dirt.
Two versions are available: one with an eyelet for threading ropes or bungee cords through and one with a hook for quick and easy attachment. There is also a separate back panel and a rubber spacer to protect the support tubes from scratches and ensure a firm hold.
Print settings & material
Printer: Any FDM printer
Material: PETG (recommended as it is weather-resistant and UV-stable), TPU for space rubber
Layer height: 0.2 mm
Infill: 20%
Support structures (Supports):
Use the ‘everywhere’ setting for support structures. This ensures that the holes and the underside of the eyelet are also printed cleanly.
Supports are also required for the clip with hook in order to print the hook stably.
Note on the spacer rubber: The supplied STL for the spacer rubber should be printed from TPU with 100% infill. This flexible material provides optimum protection for the pool pipe and ensures a non-slip connection.
You need one clamp set (consisting of two clamp halves):
2x M5x20 mm screws
2x matching M5 nuts
Important note: Do not tighten the screws completely! Leave a small gap of approx. 1 mm between the two halves of the clamp to prevent the PETG material from breaking. The tension of the rubber and the clamp ensures a secure hold.