"TiCR" bodykit for Tippmann TiPX

This is a bodykit for the Tippmann TPX or TiPX paintball pistol marker. Somewhat built around STL's found online. Some things are modified from other peoples pre-existing creations and some are my own.

The kit comes with a full top rail, front side rails and a folding buttstock. There's also a buffer tube rear cap in the files but no buttstock for it as I don't want to share the one I made, at least yet. The tube should accept any mil-spec stocks but I'm not able to confirm that.

Installation of the front section requires you to open up the marker. It replaces the front aluminium block around the barrel. The rear section is installed on the outside but it requires longer bolts as it uses the original holes for attachment. The folding stock button also requires a spring to work.

The kit allows the use of 12g CO2 capsules. It does NOT have a slot for a remote line. I don't own a remote line adapter so I can't measure the correct dimensions but there's nothing a drill/dremel couldn't handle!

The outcome is not perfect and some sections of the body are quite fragile as the walls are thin, but it works and fits straight on without any modifications to the marker. It is a good idea to also push the folding stock button when closing it to avoid too much leverage on the printed parts.

I took some rough measurements of the hardware. I can't confirm that these are the exact lengths but they're very close. I used random stuff found laying around, just shortened enough to not stick out too much and then left like that. The following numbers are measured in metric, imperial equivalents should work just fine.

Rear body:
-2 M5x40 bolts
-2 M5 nuts

Folding stock:
-2 M4x34 bolts
-2 M4x30 bolts
-1 M4x20 bolt
-4 M4 nuts
-2 M3x50 bolts
-2 M3 washers (optional)
-1 spring, 12mm long and 7mm outer diameter.

I don't know the optimal wire thickness for the spring but the inner diameter needs to be big enough to fit an M4 bolt through it. I just bent some random wire with pliers.. A 0.8mm wire might be a good starting point.

---------------

UPDATE:

I modified a few of the parts a little bit to possibly fit a remote line. I have no way to test the functionality and I don't intend to print the modified parts. There is a great chance that they don't fit at all and it's just a waste of filament and time.

The changes were made very quickly and I put close to zero effort into it so that's exactly what they look like.. The lines are not perfectly straight and that might cause problems when printing. The rear body will also be weaker than the original one as the rear end is open.

The remote line versions of the parts are added as a separate .zip file.

---------------

License info:

The "TiCR bodykit for Tippmann TiPX" by "Im-Dim" is licensed under a "CC BY-NC-SA 4.0" license. [https://creativecommons.org/licenses/by-nc-sa/4.0/]

Front body, modified from the following:

"Tipx_skull_shroud" by "Dit_Ooch", licensed under a "CC BY-NC-SA 4.0" license.
https://www.thingiverse.com/thing:3105766
https://creativecommons.org/licenses/by-nc-sa/4.0/

Rear body, modified from the following:

"Rear Picatinny Rail for Tippmann TiPX" by "chacalnoir", licensed under a "CC BY-NC 4.0" license.
https://www.thingiverse.com/thing:6221110
https://creativecommons.org/licenses/by-nc/4.0/

Folding stock, modified from the following:

"Folding Stock, EmSix" by "Patch1995", licensed under a "CC BY 4.0" license.
https://www.printables.com/model/581936-folding-stock-emsix
https://creativecommons.org/licenses/by/4.0/