Qidi XMAX3 Filament Runout and Post Extruder cutter (4mm bearing)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A Remix of the original design for a Qidi XMAX3 toolhead runout sensor and post extruder cutter.
- Ocena
- 5 / 5
- Polubienia
- 15
- Pobrania
- 62
- Wydruki
- 0
- Wyświetlenia
- 380
- Oceny
- 2
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- Creative Commons — Attribution
Only a remix of the original extruder cage to allow the usage of a 4mm bearing with a Omron D2F-L switch. I didn't have 5mm ball bearing and was missing the predrill for the switch.
Additionnaly, if you have an inductive Probe on your XMAX-3 you can connect the sensor to the toolhead directly.
For that, you need to move the black wire of the probe to the 3 pin JST XH 2.54 next to the blue wire to free the top JST XH 2P connector.
Your runout sensor will then be configured on gpio21 and the Probe z-stop on gpio11.
You need to shorten the omron switch lever to fit inside as per the pictures.
Used 2 small self tapping screws to attach it in the predrilled 1mm holes.
BOM:
Same as original
1x 4mm bearing
2x self tapping screws (1-1.5mm diameter x 10mm)
1x wired 2 pins JST 2.54mm connector (red/black as the picture)
Modify your printer.cfg probe and filament_switch sections:
[filament_switch_sensor fila]
[...] # Rest of your config
switch_pin: ^MKS_THR:gpio21[probe]
pin: ^!MKS_THR:gpio11
[...] # Rest of your config
New Homing sequence and coordinates: Stock Qidi firmware
[stepper_x]
step_pin:PB4
dir_pin:PB3
enable_pin:!PB5
microsteps:16
rotation_distance: 39.94
full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper
endstop_pin:tmc2209_stepper_x:virtual_endstop
#position_min: -7
#position_endstop:-7
#position_max:325
#homing_positive_dir:False
homing_speed:40
homing_retract_dist:0
step_pulse_duration:0.000002
filament cutter
position_min: -8 #Update for new homing procedure
position_endstop: 328 #Update for new homing procedure
position_max: 328 #Update for new homing procedure
homing_positive_dir: True
[stepper_y]
step_pin:PC14
dir_pin:PC13
enable_pin:!PC15
microsteps: 16
rotation_distance: 39.94
full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper
endstop_pin:tmc2209_stepper_y:virtual_endstop
position_min: -9.5
#position_endstop: -9.5
#homing_positive_dir: False
#position_max: 325
position_max: 335
position_endstop: 335
homing_positive_dir: True
homing_speed:40
homing_retract_dist:0
step_pulse_duration:0.000002
[homing_override]
#set_position_x:0
#set_position_y:15
#set_position_z:0
axes:xy
gcode:
{% set HOME_CUR = 1 %}
{% set driver_config = printer.configfile.settings['tmc2209 stepper_x'] %}
{% set RUN_CUR = driver_config.run_current %}
{% set HOLD_CUR = driver_config.hold_current %}
{% set home_all = (params.X is undefined) and (params.Y is undefined) and (params.Z is undefined) %}
{% set homed_axes = printer.toolhead.homed_axes %}
{% set home_z = home_all or (params.Z is defined) %}
#Always home X if Z or Y needs to home and not already homed in X
{% set home_x = home_all or (params.X is defined) or ( ((params.Y is defined) or (params.Z is defined)) and ("x" not in homed_axes) ) %}
#Always home Y if Z needs to home and not already homed in Y
{% set home_y = home_all or (params.Y is defined) or ((params.Z is defined) and ("y" not in homed_axes)) %}
G91
{% if("y" in homed_axes) %}
{% if printer.toolhead.position.y > (printer.toolhead.axis_maximum.y-15) %}
G1 Y-15 F3600
{% endif %}
{% if printer.toolhead.position.y < 40 %}
G90
G1 Y40 F3600
G91
{% endif %}
{% else %}
G1 Y-15 F3600
{% endif %}
G4 P500
{% if home_x %}
{ action_respond_info("Homing X alone") }
SET_TMC_CURRENT STEPPER=stepper_x CURRENT={HOME_CUR * 0.8}
G28 X
SET_TMC_CURRENT STEPPER=stepper_x CURRENT={HOME_CUR}
G1 X-15 F3600
{% endif %}
{% if home_y %}
{ action_respond_info("Homing Y alone") }
G90
G1 X{printer.toolhead.axis_maximum.x/2 - printer.probe["x_offset"]} F7800
G91
SET_TMC_CURRENT STEPPER=stepper_y CURRENT={HOME_CUR * 0.9}
G28 Y
SET_TMC_CURRENT STEPPER=stepper_y CURRENT={HOME_CUR}
G1 Y-15 F3600
{% endif %}
{% if home_z %}
{ action_respond_info("Homing Z alone") }
G90
G1 X{printer.toolhead.axis_maximum.x/2 - printer.probe["x_offset"]} Y{printer.toolhead.axis_maximum.y/2 - printer.probe["y_offset"]} F7800
G91
G28 Z
G1 Z25 F480
{% endif %}
#RESPOND MSG="Homing done, restoring RUN_CUR"
SET_TMC_CURRENT STEPPER=stepper_x CURRENT={RUN_CUR}
SET_TMC_CURRENT STEPPER=stepper_y CURRENT={RUN_CUR}
M204 S10000
G90</code></pre>