GridLink Art, Hidden Jigsaw Puzzle Series for Age 6 to Adult, GLH4006-100
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A low cost hidden connector tile system for creativity and exploration of colors and patterns.
- Ocena
- 0 / 5
- Polubienia
- 4
- Pobrania
- 10
- Wydruki
- 0
- Wyświetlenia
- 70
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Building Toys
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Here is a hidden-connector GridLink series designed as a slight step up in challenge, and a huge step up in capability from the simpler GridLink Play Jigsaw Set. The “age 6 to Adult” suggestion is not kidding about the adult part. Patterns panels created with this really can be suitable as wall art, chargers or placemats, etc. If well printed, they will be flat, reasonably stiff, reasonably “stuck” together by friction, with high contrast and optionally a nice textured (via textured print bed) surface.
A few hundred grams of filament in 2 colors is enough for a starter set. An example of the kind of art one can make with this is this Minecraft Creeper Face.
Unlike its larger structural cousins, GridLink Art is just thin enough with a wider tolerance, that it can be bent to allow fitting parts into inside corners where the tab cover would otherwise block it.
Don't panic at the number of parts. This is like Lego in the sense that you can be very creative with just a few shapes. But there are a lot of optional shapes to explore if you choose to.
CHOKING HAZARD WARNING:
If poorly printed, tabs could break off of these resulting in small parts that a very young child could choke on. Test the integrity of your prints before allowing children to play with them and always supervise appropriately.
KEEPING IT MANAGEABLE AND FUN:
If you have any doubt about how to start, please use the “Recommended Simple Starter Set” below. All pieces from the starter set can be reused as you or your child go on to other things.
Pick a color ‘A’ and a color ‘B’. Add all of the color ‘A’ parts to your slicer, then fill the rest of the bed with the 1x1 core tile (1x1-TTSS). While that color is in your printer, print some more of the 1x1 core tiles if you ended up with less than 10. Then repeat this for color ‘B’.
Once you have this starter set and see how they work, deciding what else you or your child will want to add will be easy.
120 of the 129 parts here are basically extra / special purpose tiles. Long story short, you can skip anything ‘L’-shaped, or that isn't 1x1 until you or your child sees that it will add to the fun. Just add those 1x1 tiles to the extra build space of your other prints, in different colors and you will soon have a great set. Add larger parts if/as you or your child see that you want them.
PRINT QUALITY / COST:
Do a short test print of two small tiles first. Tolerance is relatively high on these at 0.1mm between edges. Ideally, they should snap together and not easily shake apart. If too loose or too tight, a quick fix is to adjust your flow rate… Lower flow rate to make them looser. More flow rate to make them tighter.
You are going to want well-tuned supports to print this. Most parts have a small support to remove from inside the tab cover. My supports “Top Z Distance” is set to 0.2, and these come out easily with the corner of a putty knife.
Avoiding “Elephant foot” is important… A little too much elephant foot compensation is better than too little for these. I use 0.3 over 3 layers, but this is highly machine dependent.
Print specs assume 0.2mm layer height and 0.4mm line width. Adjust if your layer height or line width are significantly different.
Good Prints, Low Cost: Print with 2 bottom layers, 3 top layers and 2 wall loops. Rectilinear infill at 15% works well for these.
Top Quality: Print with 3 bottom layers, 4 top layers and 3 wall loops. Set rectilinear infill to 20%.
SUPPORTING YOUR FAVORITE DESIGNERS:
The Amazon links below are affiliate links, and it costs you nothing to use them. If you use an affiliate link to get to Amazon the next time you need to buy something, the designer associated with that link will get a small percentage of any sale made during that browsing session. I hope you'll pick a designer here once in a while to support in this way.
BOM:
Filament:
PLA+: https://amzn.to/3HgcjXy
Tools (optional):
A mallet can help make it easy to get these fitted and flat. Here is a good non-marking kid-sized one for supervised use: https://amzn.to/45dTMTO
INSTRUCTIONS:
Print especially the smaller shapes in various colors.
Test the prints to make sure the tabs are well printed, and all parts are safe (i.e. from tabs breaking off to become a choking hazard) for the age of the children to play with them.
See what you and your kids can make with them.
‘Likes’, ‘Follows’ and ‘Downloads’ all help to elevate goods designs, like any other social media. If you like a thing, please click ‘like’.
CHANGE LOG:
20250903: Re-arranged folders for ease of use. No model changes.