MiSTer FPGA (and Pi) 1U 10-inch Rack Mount
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
10-inch Rack Mount for a MiSTer FPGA stack, including IO board and USB board. Also supports MiSTer Pi clone board.
- Ocena
- 0 / 5
- Polubienia
- 2
- Pobrania
- 12
- Wydruki
- 0
- Wyświetlenia
- 214
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Video Games
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Description
10-inch Rack Mount for a MiSTer FPGA with 1U height. Designed for a full stack MiSTer setup, which includes a IO board and a USB board. This mount is compatible both with the original MiSTer FPGA and the MiSTer Pi clone.
If you already own a media rack, or want to create your own retrogaming mini rack, this universal mount allows you to add your MiSTer setup to it.
The mount comes with optional side panels for a full enclosure.
The User IO / SNAC port is accessible from the front, as well as three USB ports. All other ports are still accessible, but need to be routed to the back, or via keystones, to the front. A version with integrated keystone ports and a VGA opening is under consideration.
Take note: the MiSTer barely fits in 1U, so there are some vertical considerations. You will need 10mm spacers between the DE10 Nano and USB board. This is the default for the MiSTer Pi, but not the case for all third party USB boards. You may need to modify your USB bracket if it is too high for 10mm spacing.
INSTRUCTIONS – A. Rackmount
Requirements
1x MiSTer rackmount base
4x 10mm M3 spacers between USB board and DE10 Nano (this is the default for the MiSTer Pi setup)
4x M3x6 FHCS (countersunk screw) for bottom attachment
3x M3x18 FHCS (countersunk screw) for top attachment
Build Instructions
Ensure 10mm spacing between DE10 Nano board and USB board
Remove all bottom M3 screws from the MiSTer stack
Remove 3x top M3 front screws from the MiSTer stack (you can leave the screw near the VGA port in place)
Align the MiSTer stack with SNAC port facing towards the USB cutouts on the rackmount. Gently slide the MiSTer stack into the rackmount base
Insert and secure the 4x M3x6 FHCS into the bottom slots
Insert and secure the 3x M3x18 FHCS into the top slots
INSTRUCTIONS – B. Rackmount with enclosure
Requirements
1x MiSTer rackmount base
1x MiSTer rackmount side panel
1x MiSTer rackmount top panel
1x MiSTer rackmount rear panel (optional)
4x 10mm M3 spacers between USB board and DE10 Nano (this is the default for the MiSTer Pi setup)
4x M3x6 FHCS (countersunk screw) for bottom attachment
4x M3x18 FHCS (countersunk screw) for top attachment
Build Instructions
Ensure 10mm spacing between DE10 Nano board and USB board
Remove all top and bottom M3 screws from the MiSTer stack
Align the MiSTer stack with SNAC port facing towards the USB cutouts on the rackmount. Gently slide the MiSTer stack into the rackmount base
Insert and secure the 4x M3x6 FHCS into the bottom slots
(Optional) Add the rackmount rear panel. This panel by itself does not attach to anything and instead will be held together by the rackmount base and side and top panels. You might need to hold this part to keep it from falling.
Add the rackmount side panel. From the top, hold the panel at a slight angle and insert it in the space between the rackmount base and the MiSTer stack.
If you are using the rear panel, check that both panels are aligned properly. After adding the side panel, the rear panel should be held together by the rackmount base and the side panel.
Add the rackmount top panel
Insert and secure the 4x M3x18 FHCS into the top slots
Print instructions
Recommended profile | Strength |
Material | PLA, PETG (adjust material for your environment temperature!) |
Walls | 4 |
Infill | 20-25% |
Layer height | 0.2-0.24mm |
Supports | Snug (only required for rackmount base) |
There are many makers and many varieties of the IO and USB addon boards out there. I have not tested all of them. Please let me know if you have issues with tolerances, or if your board is incompatible with the case. I will make any adjustments I can.